Ericsson LBI-39055 manual Dispatcher Keyboard, Standard PC Keyboard, Video Display Monitor

Page 12

LBI-39055

Dispatcher Keyboard

The dispatcher keyboard interfaces to the PC via circuitry on the Logic Board. Its part number is P29/7590182002 (344A3927P25). This keyboard is sometimes referred to as the "custom keyboard".

Connect the dispatcher keyboard to the PC by plugging its 4-pin interlocking plug to the round socket at the Logic Board's rear cover plate. If the Logic Board is vertically orientated, this socket is located just above the female DB- 37 connector. When correctly mated, the red dot on the plug will be in a 3 o'clock or 9 o'clock position ifthe Logic Board is vertically orientated.

If disconnection is necessary, pull on the sleeve and not on the cable. Pulling on the cable will not free the latch and may damage the cable if excessive force is used.

Standard PC Keyboard

During dispatch operations, the standard PC keyboard is not used. However, during the console set-up process, access to this keyboard will be required:

(see LBI-39056 for details)

∙to start and operate the CTEST test program

∙to start the console's application program

Connect the standard PC keyboard to the PC in accordance with the manufacturer's instructions.

Video Display Monitor

Interconnect the video display monitor's video cable to the Personal Computer in accordance with the manufacturer's instructions.

AUDIO TOWER

All Audio Tower-related cables should be routed out of the bottom of the case through the cut-out in the bottom of the rear door. If necessary, some or all of the cables can be routed under the case's stand and out to the front of the Audio Tower. Secure the cables with cable ties as necessary.

∙ for file management (for example - AUTOEXEC.BAT and CONFIG.SYS file changes may be necessary)

∙ to configure certain items via the Editor program

Desk Mic (if used)

Connect the desk microphone (option CRMC3D or equivalent) to the Audio Tower by mating its male DB-9 connector to the female DB-9 connector labeled "DESK

TABLE 6 − C3 MAESTRO-TO-CEC/IMC AUDIO LINE REQUIREMENTS

AUDIO PA BOARD #1

AUDIO PA BOARD #2

AUDIO MATRIX BOARD LABELING

C3 MAESTRO DESIGNATION

CEC/IMC DESIGNATION

CONSOLE

CEC/IMC

SELECT SPEAKER/HEADSET

MICROPHONE

UNSELECT SPEAKER #1

UNSELECT SPEAKER #2

UNSELECT SPEAKER #3 *

CALL DIRECTOR PATCH

LINE A

 

LINE B

 

 

 

 

 

 

 

LINE A

 

LINE B

 

 

 

 

 

 

 

LINE 1

 

LINE 2

 

 

 

 

 

 

 

IN

 

OUT

 

IN

 

OUT

 

 

 

 

 

 

 

OUT

 

IN

 

OUT

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

 

 

 

 

 

 

 

 

 

 

 

 

 

X

XX

LINE A

LINE C

LINE 3

 

IN

OUT

 

 

 

 

OUT

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

XX

LINE B

LINE D

LINE 4

 

IN

 

OUT

 

 

 

 

 

OUT

 

IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

XX

XX XX

"X" = 2-wire connection always required

"XX"= 2-wire connection required if console is so equipped

*= Unselect speaker #3 not available if console is equipped with Call Director patch

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Table of Contents LBI-39055Table of Contents LBI-39055General − C3 Maestro Equipment InterconnectionsBoard SET-UP Personal ComputersLogic Board Installation Into The PC FirmwareAudio PA Boards PLUG-IN RS-422 Board OptionalInterconnecting Equipment Audio Matrix BoardBoard Software Installation and SET-UP CEC/IMC InterconnectionsControl Data Link Remote Console Interconnections Via a 4-Wire Modem ∙ Modem OptionsMNP Options DTE OptionsAudio Links Personal ComputerPC-To-Audio Tower Interconnect Cable − CEC/IMC-To-C3 Maestro Interconnections Co-Located LBI-39055 Dispatcher Keyboard Standard PC KeyboardVideo Display Monitor Desk Mic if usedBoom/Gooseneck PTT and Monitor Switches if used − BOOM/GOOSENECK MIC Wiring Wire Color DB-9 PIN NumberHeadset Jacks if used Boom/Gooseneck Mic if usedFootswitches if used Volume Controller Box if usedSpeakers if used Pager Input if used Recorder Outputs if usedRelay Outputs if used Call Director if equipped Equipment Room GroundingConsole-to-CEC/IMC Audio Interconnections Console-to-Call Director Interconnections− I/O BOARD-TO-CALL Director Signal Descriptions Type Input OutputPOWER-UP Procedure Software Installation SET-UP ProcedureAC Power and UPS Equipment PC Cmos SET-UP ProgramSoftware Installation and Upgrades File Directories and ContentsEditor Program Running the C3 Maestro Application Program Console User Profile Configuration Database InitializationSystem Manager Database Uploads System Tests LOW-LEVEL TestsSend Line B Input Audio to Speaker B Send Mic Audio To Line a & Line B OutputsTest Audio PA Board #2 if installed HIGH-LEVEL TestsCompletion
Top Page Image Contents