Multiquip MC3H, MC3SE operation manual MIX N GO Mixer Initial START-UP Electric Motor

Page 22

MIX N' GO MIXER — INITIAL START-UP (ELECTRIC MOTOR)

Initial Start-up Instructions (Electric Motor)

Starting

CAUTION:

DO NOT attempt to operate the mixer until the Safety, General Information and Inspection sections have been read and understood.

1.Before starting, make sure mixer is positioned on a secure flat surface to prevent tipping.

2.Use an extension cord (see Table 5) of adequate current carrying capacity, insert the electric motor's power plug into one end of the extension cord.

3.NEVER! use a worn or frayed extension cord.

4.NEVER! operate mixer withV-belt cover removed.

5.Plug the other end of the extension cord into a 120 VAC G.F.C.I.protected receptacle. Rememberthepowerrequire- ments for this electric motor is 120 VAC, 60 Hz. The use of any other input voltage will severely damage the motor.

WARNING:

ALWAYS read the label on the electric motor before applying power.The label will indicate the proper power requirements for the motor. Remember the use of any other input voltage will severely damage the motor.

WARNING:

To prevent tripping (Figure 18) of both the mixer and personnel, position the extension cord so that it lays flat and is not curled underneath the mixer.

Table 5. Extension Cord Size

No. 12 Wire

No. 10 Wire

No. 8 Wire

No. 6 Wire

 

 

 

 

50 (feet)

75 (feet)

100 (feet)

200 (feet)

(15.24 meters)

(22.86 meters

(30.48 meters

(60.96 meters

 

 

 

 

DANGER

NEVER! touch the power cord (Figure 17) with wet hands or while standing in water when it is connected to a power source.The possibly exists of electrical shock (electrocution) even death. NEVER! spray

water directly on the electric motor.

WET

HANDS

POWER

CORD

(POWER ON)

Figure 17. Extension Cord (Wet Hands)

Figure 18. Mixer (Tripping)

6.The drum should be rotating allowing the mixing process to begin. Use a shovel (Figure 19) to place the cement mix inside the drum, add water as required. Be careful to only placethe tipoftheshovelinsidethedrum.Placingtheshovel all the way inside the drum will cause the shovel to strike the blades. This condition will make the shovel rotate, and could cause injury to personnel.

Figure 19. Mixing Drum (Placing cement Mix))

6.SeeTable 3 for mixing hints.NEVER! place hands inside the drum while the drum is rotating.

PAGE 22 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)

Image 22
Contents MIX N GO Mini Concrete Mixer Steel Drum Models Page Heres HOW to GET Help Table of Contents UPS Ground Service at no charge for freight Parts Ordering ProceduresUPS Third Day Service at one-half of actual freight cost MIX N GO Mixer Safety Message Alert Symbols Seriously injured if you do not follow directionsAlways wear approved respiratory protection InstructionsGeneral Safety Rules for Safe OperationRules for Safe Operation Emergencies Operation and Safety Decals Machine Safety DecalsOperation and Safety Decals Advertencia AvertissementDry Net Weight MIX N GO Mixer SpecificationsDimensions L x W x H ModelMIX N GO Mixer Dimensions Mixer MIX N GO Mixer Dimensions Electric Motor MIX N GO Mixer General Information MIX N GO Mixer Mixer Components MIX N GO Mixer Basic Engine Do not spin the drum on fast, as this may AssemblyDamage the gearbox MIX N GO Mixer Assembly Instructions Do not tilt the mixer on a wet, smooth or slippery surfaceEngine Oil Check Before StartingBelt Check Initial Start-up Instructions Electric Motor Starting MIX N GO Mixer Initial START-UP Electric MotorWater directly on the electric motor Starting the Engine Honda engine Place the engine ON/OFF switch in the on positionPlace the trowels throttle lever to the Idle position MIX N GO Mixer Initial START-UP Gasoline Engine Starter GripMaintenance Gearbox Oil Check MIX N GO Mixer MaintenanceGerarbox Removal MIX N GO Mixer Maintenance Gasoline Engine Engine Maintenance ScheduleEngine Air Cleaner Spark Plug GapMIX N GO Mixer Preparation for Long -TERM Storage Page MIX N GO Mixer Troubleshooting Engine Engine TroubleshootingMIX N GO Mixer Troubleshooting ENGINE/MIXER MIX N GO Mixer Explanation of Code in Remarks Column Items Found In the Items Number ColumnTo 3 Units MIX N GO Mixer Name Plate and Decals Decalwarning MQ MIX N GO Mixer Mixer Assy Part Name QTY Remarks OIL Filler Plug M14 x 2 x 15LHonda G100K2QA2 Engine AIR Cleaner Assy TUBE, Breather Honda G100K2QA2 Engine Camshaft Assy Part Name Honda G100K2QA2 Engine Carburetor Assy Gasket SET Honda G100K2QA2 Engine Control Assy ARM, Governor Honda G100K2QA2 Engine Crankcase Cover Assy Crankcase Cover 1 Assy Honda G100K2QA2 Engine Crankshaft Assy 13310ZG0601 Honda G100K2QA2 Engine Cylinder Barrel Assy GUIDE, Valve OS Optional Honda G100K2QA2 Engine FAN Cover Assy 19610ZG0W20ZB Honda G100K2QA2 Engine Flywheel Assy FAN, Cooling Honda G100K2QA2 Engine Fueltank Assy 17510ZG0W00ZA Bulk HOSE, Fuel 4.5X3000Page Honda G100K2QA2 Engine Gasket KIT Assy Honda G100K2QA2 Engine Ignition Coil Assy CAP, Ignition Toyo Honda G100K2QA2 Engine Muffler Assy Muffler W/PROTECTOR Honda G100K2QA2 Engine Piston Assy Piston Standard Honda G100K2QA2 Engine Recoil Starter Assy Recoil Starter 3 Assy Honda G100K2QA2 Engine Labels Part Name QTY. Remarks Terms and Conditions of Sale Parts Page Multiquip INC
Related manuals
Manual 42 pages 47.51 Kb