Multiquip MC3H, MC3SE operation manual MIX N GO Mixer General Information

Page 16

MIX N' GO MIXER — GENERAL INFORMATION

APPLICATION

This mixer is only intended for the production of concrete, mortar and plaster. The mixer must be used for its intended purposes and is not suitable for the mixing of flammable or explosive substances. The mixer must not be used in an explosive atmosphere.

POWER PLANTS

This portable mixer is powered by either a Honda G100K2, 4-stroke, side valve, single cylinder, gasoline engine rated at 2.5 hp @3,600 rpm. or a 0.75 hp electric motor.

DRUM ASSEMBLY

The drum is instantly removable by unscrewing counter- clockwise. When inserting drum onto gearbox shaft, make sure that drum is fully screwed onto shoulder or threads may be damaged. Use extreme care when screwing on the drum, spinning drum onto the gearbox shaft too fast may damage gearbox.

ELECTRICAL

If mixer is equipped with an electric motor, make sure that the power being supplied to the motor corresponds to the voltage rating label on the motor. Supplying the wrong voltage to the electric motor will cause severe electrical damage to the motor.

Always make sure that OFF/ON switch on the electric motor is in the OFF position before applying power.

It is strongly recommended that when plugging in the mixer's power cord into a receptacle, that a G.F.C.I. (Ground Fault Current Interrupter) receptacle be used.

EXTENSION CABLES

The extension cable should be a 3-wire configuration that includes a ground wire that conforms to UL code. The wire cross section must be a minimum of 2.5 mm2 . Choose an extension cord of adequate current carrying as Reference in Table 5. Remember distance affects the wire size of the extension cable.

Ensure that the extension cable is carefully laid out avoid- ing wet areas, sharp edges and locations where vehicles might run over it. Avoid allowing the extension cable to be trapped underneath the mixer.

Unroll the extension cable fully or it will overheat and could catch fire. Make sure that all extension cable connections are dry and safe. Replace any defective or badly worn ex- tension cable immediately.

PORTABLE GENERATORS

When using a portable generator it must have a minimum output of 2.5 kw and be continuous rated.

GEARBOX

The gearbox oil level has been preset at the factory prior to shipping. Before inspecting the gearbox oil level (Figures 30 and 31), make sure the gearbox is cold before removing the filler plug. Fill up with EP90. or similar gear oil.

TRANSPORTINGTHE MIXER

Use a ramp (Figure 3) to load and unload the mixer from the transport vehicle. Never drop the mixer onto the ground; damage to the mixer could result.

Figure 3. Mixer Loading

PAGE 16 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV. #1 (09/09/02)

Page 15 Page 17
Image 16
Page 15 Page 17
Contents MIX N GO Mini Concrete Mixer Steel Drum Models Page Heres HOW to GET Help Table of Contents UPS Ground Service at no charge for freight Parts Ordering ProceduresUPS Third Day Service at one-half of actual freight cost MIX N GO Mixer Safety Message Alert Symbols Seriously injured if you do not follow directionsAlways wear approved respiratory protection InstructionsGeneral Safety Rules for Safe OperationRules for Safe Operation Emergencies Operation and Safety Decals Machine Safety DecalsOperation and Safety Decals Advertencia AvertissementMIX N GO Mixer Specifications Dimensions L x W x HDry Net Weight ModelMIX N GO Mixer Dimensions Mixer MIX N GO Mixer Dimensions Electric Motor MIX N GO Mixer General Information MIX N GO Mixer Mixer Components MIX N GO Mixer Basic Engine Do not spin the drum on fast, as this may AssemblyDamage the gearbox MIX N GO Mixer Assembly Instructions Do not tilt the mixer on a wet, smooth or slippery surfaceEngine Oil Check Before StartingBelt Check Initial Start-up Instructions Electric Motor Starting MIX N GO Mixer Initial START-UP Electric MotorWater directly on the electric motor Starting the Engine Honda engine Place the engine ON/OFF switch in the on positionPlace the trowels throttle lever to the Idle position MIX N GO Mixer Initial START-UP Gasoline Engine Starter GripMaintenance Gearbox Oil Check MIX N GO Mixer MaintenanceGerarbox Removal MIX N GO Mixer Maintenance Gasoline Engine Engine Maintenance ScheduleEngine Air Cleaner Spark Plug GapMIX N GO Mixer Preparation for Long -TERM Storage Page MIX N GO Mixer Troubleshooting Engine Engine TroubleshootingMIX N GO Mixer Troubleshooting ENGINE/MIXER MIX N GO Mixer Explanation of Code in Remarks Column Items Found In the Items Number ColumnTo 3 Units MIX N GO Mixer Name Plate and Decals Decalwarning MQ MIX N GO Mixer Mixer Assy Part Name QTY Remarks OIL Filler Plug M14 x 2 x 15LHonda G100K2QA2 Engine AIR Cleaner Assy TUBE, Breather Honda G100K2QA2 Engine Camshaft Assy Part Name Honda G100K2QA2 Engine Carburetor Assy Gasket SET Honda G100K2QA2 Engine Control Assy ARM, Governor Honda G100K2QA2 Engine Crankcase Cover Assy Crankcase Cover 1 Assy Honda G100K2QA2 Engine Crankshaft Assy 13310ZG0601 Honda G100K2QA2 Engine Cylinder Barrel Assy GUIDE, Valve OS Optional Honda G100K2QA2 Engine FAN Cover Assy 19610ZG0W20ZB Honda G100K2QA2 Engine Flywheel Assy FAN, Cooling Honda G100K2QA2 Engine Fueltank Assy 17510ZG0W00ZA Bulk HOSE, Fuel 4.5X3000Page Honda G100K2QA2 Engine Gasket KIT Assy Honda G100K2QA2 Engine Ignition Coil Assy CAP, Ignition Toyo Honda G100K2QA2 Engine Muffler Assy Muffler W/PROTECTOR Honda G100K2QA2 Engine Piston Assy Piston Standard Honda G100K2QA2 Engine Recoil Starter Assy Recoil Starter 3 Assy Honda G100K2QA2 Engine Labels Part Name QTY. Remarks Terms and Conditions of Sale Parts Page Multiquip INC
Related manuals
Manual 42 pages 47.51 Kb
Top Page Image Contents