Stow MS15E, MS15H5.5 manual Stopping the Mixer Electric Motor, Do not Disconnect

Page 23

MS15H/MS15E MIXER — START-UP PROCEDURES

4.Turn the engine switch (Figure 12) to the ON position.

Figure 12. Engine ON/OFF Switch (ON)

Be sure to stand clear of the dump handle when the mixer

NOTEis operational. Any binding of material between the mixer blades and the drum will cause the drum handle to move to the discharge position, thus causing bodily harm.

Stopping the Mixer (Electric Motor)

1.Place the engine ON/OFF switch (Figure 14) in the OFF position.

7.Pull the starter grip (Figure 13) lightly until you feel resistance, then pull briskly. Return the starter grip gently.

Figure 13. Starter Grip

Starting (electric only)

1.Using an adequate size extension cord (see Table 4), connect one end of the extension cord to the plug on the electric motor, connect the other end to the power source. Make sure the motor is configured for the proper operating voltage.

2.Set the electric motor's ON/OFF switch (Figure 5) to the ON position.

Mixing Dumping

1.The paddle shaft inside the drum should be rotating at this time.

2.Lift the mixing bag compound onto the steel grate over the bag cutter and let the contents fall into the drum.

3.Add water, and mix compound to desired consistency.

Figure 14. Engine ON/OFF Switch (OFF)

2.Place the fuel shut-off valve in the OFF position.

3.Disconnect the spark plug wire.

4.Clean drum of all debris and foreign matter.

5.Store mixer in a clean dry location.

 

DANGER

DO NOT Disconnect

 

the Start/Stop Switch

 

 

NEVER disable or disconnect the start/stop switch. It is provided for operator safety. Serious Injury may result if it is disabled, disconnected or improperly maintained.

Stopping the Mixer (Electric Motor)

1.Place the electric motor's ON/OFF switch in the OFF position.

2.Disconnect the electric motor's extension cord from its power source.

3.Clean drum of all debris and foreign matter.

4.Store mixer in a clean dry location.

MQ STOW MS15H/MS15E MIXER — PARTS & OPERATION MANUAL — REV. FINAL (08/10/06) — PAGE 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PLASTER/MORTAR Mixer Page Heres HOW to GET Help Table of Contents When ordering parts Please supply the following information MS15H/MS15E Mixer Parts Ordering ProceduresMS15H/MS15E Mixer Specifications MS15H/MS15E Mixer Dimensions Burn Hazards HazardsEquipment Damage MS15H/MS15E Mixer Safety Message Alert SymbolsRead this manual MS15H/MS15E Mixer Rules for Safe OperationStand Clear Mixer when in useMS15H/MS15E Mixer Rules for Safe Operation MaintenanceMS15H/MS15E Mixer Operation and Safety Decals MS15H/MS15E Mixer General Information Mixer Components MS15H/MS15E Mixer Mixer ComponentsMS15H/MS15E Mixer Basic Engine Components Electric Motor MS15H/MS15E Mixer Electric MotorMS15H/MS15E Mixer Electric Motor Paddle Blade Adjustment, Steel Drum MS15H/MS15E Mixer Paddle Blade AdjustmentExplosive Fuel Before StartingEyesight and Hearing InspectionBlade Check Start/Stop SwitchControls Start/Stop Switches Belt CheckMS15H/MS15E Mixer START-UP Procedures Do not Disconnect Stopping the Mixer Electric MotorEngine Maintenance Schedule MS15H/MS15E Mixer Maintenance EngineDrum Bearing Bracket Lubrication Grease Fittings Zerk Maintenance Electric MotorDrum Head Seals Countershaft Bearing LubricationMS15H/MS15E Mixer Maintenance Mixer MS15H/MS15E Mixer -TROUBLESHOOTING Engine MS15H/MS15E Mixer -TROUBLESHOOTING Engine MS15H/MS15E Mixer -TROUBLESHOOTING MIXER/MOTOR MS15H/MS15E Mixer -WIRING Diagram Electric Motor Page Items Found In the Remarks Column Explanation of Code in Remarks ColumnMS15H/MS15E Mixer 1TO 3 Units With Honda GX160K1HX2 Engine MS15H/MS15E Mixer Suggested Spare PartsMS15H/MS15E Mixer Nameplate and Decals Part Name MS15H/MS15E Mixer Steeltub Assy MS15H/MS15E Mixer Steeltub Assy MS15H/MS15E Mixer Paddle Shaft Assy Paddle Shaft MS15H/MS15E Mixer Frame Assy Part Name QTY MS15H/MS15E Mixer Engine Cover Assy Retainer Chain MS15H/MS15E Mixer Honda Engine Assy Honda Engine Assy MS15H/MS15E Mixer Electric Motor Assy Pillow Block Honda GX160K1HX2 Engine Cylinder Head Assy Part Name QTY Remarks Honda GX160K1HX2 Engine Cylinder Barrel Assy Switch ASSY. OIL Level Honda GX160K1HX2 Engine Crankcase Cover Assy GASKET, OIL Filler CAP Honda GX160K1HX2 Engine Crankshaft Assy Crankshaft H- Type Honda GX160K1HX2 Engine Piston Assy Ring SET, Piston STD Honda GX160K1HX2 Engine Camshaft Assy ROD, Push Honda GX160K1HX2 Engine Recoil Starter Assy REEL, Recoil Starter Honda GX160K1HX2 Engine FAN Cover Assy PLATE, Side STD Honda GX160K1HX2 Engine Carburetor Assy Gasket SET Honda GX160K1HX2 Engine AIR Cleaner Assy Gasket Elbow Honda GX160K1HX2 Engine Muffler Assy Muffler Comp Honda GX160K1HX2 Engine Fueltank Assy RUBBER, Supporter Honda GX160K1HX2 Engine Flywheel Assy FAN, Cooling Honda GX160K1HX2 Engine Ignition Coil Assy Coil ASSY., Ignition Honda GX160K1HX2 Engine Control Assy ARM, Governor Honda GX160K1HX2 Engine Gear Reduction Assy CASE, Reduction Honda GX160K1HX2 Engine Label Assy Enblem Terms and Conditions of Sale Stow Construction Equipment Page Your Local Dealer is

MS15E, MS15H5.5 specifications

The Stow MS15H5.5 and MS15E represent advanced options in the realm of industrial cleaning machinery, specifically designed for effectiveness and efficiency in various cleaning applications. These models cater to the demands of different environments, such as warehouses, retail spaces, and manufacturing facilities.

The MS15H5.5 is powered by a robust Honda engine, delivering superior cleaning power while ensuring reliability and longevity. This model features a high-pressure washer that efficiently tackles tough grime and stains, making it ideal for heavy-duty cleaning tasks. The Honda engine is known for its fuel efficiency, allowing for longer operational use without frequent refueling. It boasts a durable design with a reinforced steel frame, providing stability and toughness to withstand rigorous use.

On the other hand, the MS15E is an electric model that offers a quieter alternative for cleaning operations where noise reduction is crucial. This electric version is equipped with a powerful motor that provides consistent pressure for effective cleaning. The MS15E is valued for its ease of use and lower maintenance requirements compared to its gas-powered counterpart. Users appreciate its lightweight construction, which makes it easily maneuverable for various cleaning tasks.

Both the MS15H5.5 and MS15E incorporate advanced technology features such as an adjustable pressure setting, giving users better control over the cleaning intensity based on the surface being cleaned. This feature not only enhances cleaning efficacy but also extends the lifespan of the equipment and surfaces being serviced.

Safety is another critical aspect of both models. They come equipped with thermal relief valves that prevent overheating, ensuring safe operation during prolonged use. The ergonomic design of the handles and controls provides comfort to the operator, reducing fatigue during extended periods of cleaning.

In summary, the Stow MS15H5.5 and MS15E are versatile cleaning machines that excel in performance, durability, and user-friendliness. Whether powered by gas or electricity, these models are designed to tackle various cleaning challenges effectively, making them valuable assets for any cleaning operation.
Top Page Image Contents