Stow manual Stow MS-70 PLASTER/MORTAR Mixer Basic Engine Components, Fuel Hazard, Burn Hazard

Page 17

STOW MS-70 PLASTER/MORTAR MIXER — BASIC ENGINE COMPONENTS

Figure 6. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing.

5.

FuelValve Lever – OPEN to let fuel flow, CLOSE to stop

 

the flow of fuel.

6.

Choke Lever – Used in the starting of a cold engine, or in

 

cold weather conditions. The choke enriches the fuel

 

mixture.

1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.

DANGER Explosive

Fuel Hazard

Adding fuel to the tank should be done only when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue

has been completely wiped up, and the area surrounding the engine is dry.

2. Throttle Lever – Used to adjust engine RPM speed (lever advanced forward SLOW, lever back toward operator FAST).

3.

Engine ON/OFF Switch – ON position permits engine

 

starting, OFF position stops engine operations.

4.

Recoil Starter (pull rope) – Manual-starting method. Pull

 

the starter grip until resistance is felt, then pull briskly and

 

smoothly.

7. Air Cleaner – Prevents dirt and other debris from entering the fuel system. Remove wing-nut on top of air filter cannister to gain access to filter element.

Operating the engine without an air

filter, with a damaged air filter, or a filter

NOTE in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

 

WARNING

Burn Hazard

 

 

 

Enginecomponentscangenerateextremeheat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating. NEVER operate the engine with the muffler removed.

8. Spark Plug – Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean spark plug once a week.

9. Muffler – Used to reduce noise and emissions.

10. Fuel Tank – Holds unleaded gasoline. For additional information refer to engine owner's manual.

STOW MS-70 MIXER — OPERATION MANUAL — REV. #3 (03/26/10) — PAGE 17

Image 17
Contents Model MS-70 Page Heres HOW to GET Help Stow MS-70 PLASTER/MORTAR Mixer Table of Contents Direct TOLL-FREE access to our Parts Department Mixer Specifications Dimensions Stow MS-70 PLASTER/MORTAR Mixer DimensionsRespiratory Hazards Burn HazardsEquipment Damage Stow MS-70 Mixer Safety Message Alert SymbolsRead this manual Stow MS-70 PLASTER/MORTAR Mixer Rules for Safe OperationStand Clear Mixer when in useTow Bar toVehicle Connection Coupler Only Towing Safety Precautions Regularly InspectReplacing Mixer Tow Bar Vehicle Connection Pintle and LoopWhen Towing Stow MS-70 PLASTER/MORTAR Mixer Safety Chain ConnectionAlways Tow with Tow Bar to Mixer ConnectionMachine Safety Decals MS-70 PLASTER/MORTAR Mixer Operation and Safety DecalsStow MS-70 PLASTER/MORTAR Mixer General Information Engine MaintenanceMixer Components Stow MS-70 PLASTER/MORTAR Mixer Basic Mixer ComponentsBurn Hazard Stow MS-70 PLASTER/MORTAR Mixer Basic Engine ComponentsFuel Hazard Electric Motor Connection Stow MS-70 PLASTER/MORTAR Mixer Electric MotorElectric Motor Electric MotorVoltage Switch Stow MS-70 Paddle Blade Adjustment Steel Drum Before Starting Stow MS-70 PLASTER/MORTAR Mixer InspectionInspection Engine Oil CheckControls Start/Stop Switches Start/Stop SwitchExplosive Fuel Belt CheckRespiratory Hazard Stow MS-70 PLASTER/MORTAR Mixer START-UP ProceduresGeneral Safety Engine ON/OFF Switch MS-70 PLASTER/MORTAR Mixer START-UP ProceduresStow MS-70 PLASTER/MORTAR Mixer OPERATION/SHUT-DOWN Dump Handle SafetyStow MS-70 PLASTER/MORTAR Mixer Maintenance Engine Hazard Stow MS-70 PLASTER/MORTAR Mixer Maintenance EngineDrum Head Seals Ball Socket and Clamp Face MaintenanceDrum Bearing Bracket Lubrication LubricatingMain Gear and Drive Pinion Alignment Stow MS-70 PLASTER/MORTAR Mixer Maintenance MixerDamagedWheels Tires/Wheels/Lug NutsTires Wear/Inflation Eyesight HazardStart all wheel lug nuts by hand Lug Nut Torque RequirementsSuspension Mixer CleaningKeep Hands Mixer StorageEngine Troubleshooting Stow MS-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING EngineWhite Mixer Troubleshooting Stow MS-70 -TROUBLESHOOTING MIXER/ELECTRIC MotorStow MS-70 Mixer Wiring Diagram Electric Motor Page Items Found In the Items Number Column BookItems Found In the Remarks Column Part numbers on this Stow MS-70 Mixer Suggested Spare PartsNameplate and Decals DECAL, Warning Safety Grate DECAL, Safety InstructionsSee Operation and Safety Decals DECAL, Towing InstructionsFrame Assy LOCK, PIN Safety ChainCotter PIN Spring Locking PINPaddle Shaft Assy INSERT, Paddle ARM Paddle ShaftPaddle ARM, Engine END WASHER, Flat 1/2Steel Drum Assy Stow MS-70 Mixer Steel Drum AssyCAP, Dust Drum Bearing BracketSeparately FITTING, GreaseDrum and Paddle Shaft Complete Assy Stow MS-70 Mixer Drum & Paddle Shaft Complete AssyPIN Cotter Bearing SealedCAP, Grease Fitting Axle Assy LUG Nuts Dust CAPTire and RIM, Carlise Castle NUTEngine Assy Pillow Block Bearing Flat Washer 3/8RING, Retainer Pinion GearStow MS-70 Mixer Electric Motor Assy Electric Motor 1.5 HP Shaft and PinionCabinet Assy Wire Harness SWITCH, PUSH-PULLIncludes Items W Rubber ProtectorAIR Cleaner Assy COVER, AIR Cleaner ELEMENT, AIR CLEANER, DualGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy Camshaft SPRING, Weight ReturnROD Push ARM Valve RockerCarburetor Assy Gasket SET PLATE, Lever SettingValve SET, Float Float SETControl Assy ROD, Governor ARM, GovernorSPRING, Governor SPRING, Throttle ReturnCrankcase Cover Assy HOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Cylinder Barrel Assy SHAFT, Governor ARM Switch ASSY., OIL LevelBOLT, Drain Plug Ring 14MM AraiCylinder Head Assy GUIDE, EX. VALVE, OS, Optional GUIDE, VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy CLIP, Wire Harness Switch ASSY., Engine StopCLIP, Tube ShroudFlywheel Assy Flywheel Comp FAN, CoolingNUT, Special 16MM KEY, Special WoodruffMuffler Assy PROTECTOR, Muffler MufflerPROTECTOR, EX. Pipe PIPE, EXFuel Tank Assy JOINT, Fuel Tank Rubber Supporter 107MMTank COMP., Fuel *NH1*, Black GASKET, Fuel Filler CAPIgnition Coil Assy WIRE, Stop Switch 370MM GROMMET, WireCoil ASSY., Ignition CAP ASSY., Noise SuppressorPiston Assy Ring SET, PISTON, STD BOLT, Connecting RODRing SET, PISTON, 0.75, Optional PISTON, StandardRecoil Starter Assy RATCHET, Starter PULLEY, Recoil StarterSPRING, Friction SPRING, Starter ReturnGear Reduction Assy Countershaft GEAR, Primary Drive 17TSHAFT, P.T.O. H- Type Shim a OptionalLabel Assy EMBLEM, Internal Labels AssyMARK, CAUTION, External LABEL, CautionTerms and Conditions of Sale Stow Construction Equipment Page HERE’S HOW to GET Help