Stow MS-70 manual Lug Nut Torque Requirements, Start all wheel lug nuts by hand

Page 31

STOW MS-70 PLASTER/MORTAR MIXER — MAINTENANCE (MIXER)

Lug Nut Torque Requirements

It is extremely important to apply and maintain proper wheel mounting torque. Be sure to use only the fasteners matched to the cone angle of the wheel. Proper procedure for attach- ment of the wheels is as follows:

1.Start all wheel lug nuts by hand.

2.Torque all lug nuts in sequence. See Figure 34. DO NOT torquethewheellugnutsallthewaydown.Tighteneachlug nut in 3 separate passes as defined by Table 10.

Table 10. Tire Torque Requirements

 

 

 

 

Wheel Size

First Pass

Second Pass

Third Pass

 

FT-LBS

FT-LBS

FT-LBS

 

 

 

 

12"

20-25

35-40

50-65

 

 

 

 

13"

20-25

35-40

50-65

 

 

 

 

14"

20-25

50-60

90-120

 

 

 

 

15"

20-25

50-60

90-120

 

 

 

 

16"

20-25

50-60

90-120

 

 

 

 

NOTE

NEVER! use an pneumatic air gun

to tighten wheel lug nuts.

3.Afterfirstroaduse,retorquealllugnutsinsequence.Check all wheel lug nuts periodically.

Figure 34. Wheel Lug Nuts Tightening Sequence

STOW MS-70 MIXER — OPERATION MANUAL — REV. #3 (03/26/10) — PAGE 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model MS-70 Page Heres HOW to GET Help Stow MS-70 PLASTER/MORTAR Mixer Table of Contents Direct TOLL-FREE access to our Parts Department Mixer Specifications Dimensions Stow MS-70 PLASTER/MORTAR Mixer DimensionsRespiratory Hazards Burn HazardsEquipment Damage Stow MS-70 Mixer Safety Message Alert SymbolsRead this manual Stow MS-70 PLASTER/MORTAR Mixer Rules for Safe OperationStand Clear Mixer when in useMixer Tow Bar Vehicle Connection Pintle and Loop Towing Safety Precautions Regularly InspectTow Bar toVehicle Connection Coupler Only ReplacingTow Bar to Mixer Connection Stow MS-70 PLASTER/MORTAR Mixer Safety Chain ConnectionWhen Towing Always Tow withMachine Safety Decals MS-70 PLASTER/MORTAR Mixer Operation and Safety DecalsStow MS-70 PLASTER/MORTAR Mixer General Information Engine MaintenanceMixer Components Stow MS-70 PLASTER/MORTAR Mixer Basic Mixer ComponentsFuel Hazard Stow MS-70 PLASTER/MORTAR Mixer Basic Engine ComponentsBurn Hazard Electric Motor Stow MS-70 PLASTER/MORTAR Mixer Electric MotorElectric Motor Connection Electric MotorVoltage Switch Stow MS-70 Paddle Blade Adjustment Steel Drum Engine Oil Check Stow MS-70 PLASTER/MORTAR Mixer InspectionBefore Starting InspectionBelt Check Start/Stop SwitchControls Start/Stop Switches Explosive FuelGeneral Safety Stow MS-70 PLASTER/MORTAR Mixer START-UP ProceduresRespiratory Hazard Engine ON/OFF Switch MS-70 PLASTER/MORTAR Mixer START-UP ProceduresStow MS-70 PLASTER/MORTAR Mixer OPERATION/SHUT-DOWN Dump Handle SafetyStow MS-70 PLASTER/MORTAR Mixer Maintenance Engine Hazard Stow MS-70 PLASTER/MORTAR Mixer Maintenance EngineLubricating Ball Socket and Clamp Face MaintenanceDrum Head Seals Drum Bearing Bracket LubricationMain Gear and Drive Pinion Alignment Stow MS-70 PLASTER/MORTAR Mixer Maintenance MixerEyesight Hazard Tires/Wheels/Lug NutsDamagedWheels Tires Wear/InflationStart all wheel lug nuts by hand Lug Nut Torque RequirementsMixer Storage Mixer CleaningSuspension Keep HandsEngine Troubleshooting Stow MS-70 PLASTER/MORTAR Mixer -TROUBLESHOOTING EngineWhite Mixer Troubleshooting Stow MS-70 -TROUBLESHOOTING MIXER/ELECTRIC MotorStow MS-70 Mixer Wiring Diagram Electric Motor Page Items Found In the Remarks Column BookItems Found In the Items Number Column Part numbers on this Stow MS-70 Mixer Suggested Spare PartsNameplate and Decals DECAL, Towing Instructions DECAL, Safety InstructionsDECAL, Warning Safety Grate See Operation and Safety DecalsFrame Assy Spring Locking PIN Safety ChainLOCK, PIN Cotter PINPaddle Shaft Assy WASHER, Flat 1/2 Paddle ShaftINSERT, Paddle ARM Paddle ARM, Engine ENDSteel Drum Assy Stow MS-70 Mixer Steel Drum AssyFITTING, Grease Drum Bearing BracketCAP, Dust SeparatelyDrum and Paddle Shaft Complete Assy Stow MS-70 Mixer Drum & Paddle Shaft Complete AssyCAP, Grease Fitting Bearing SealedPIN Cotter Axle Assy Castle NUT Dust CAPLUG Nuts Tire and RIM, CarliseEngine Assy Pinion Gear Flat Washer 3/8Pillow Block Bearing RING, RetainerStow MS-70 Mixer Electric Motor Assy Electric Motor 1.5 HP Shaft and PinionCabinet Assy Rubber Protector SWITCH, PUSH-PULLWire Harness Includes Items WAIR Cleaner Assy COLLAR, AIR Cleaner ELEMENT, AIR CLEANER, DualCOVER, AIR Cleaner GROMMET, AIR CleanerCamshaft Assy ARM Valve Rocker SPRING, Weight ReturnCamshaft ROD PushCarburetor Assy Float SET PLATE, Lever SettingGasket SET Valve SET, FloatControl Assy SPRING, Throttle Return ARM, GovernorROD, Governor SPRING, GovernorCrankcase Cover Assy Type Balancer WEIGHT, GovernorHOLDER, Governor Weight PIN, Governor WeightCrankshaft Assy Weight Balancer Cylinder Barrel Assy Ring 14MM Arai Switch ASSY., OIL LevelSHAFT, Governor ARM BOLT, Drain PlugCylinder Head Assy GASKET, Cylinder Head GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional CLIP, Valve GuideFAN Cover Assy Shroud Switch ASSY., Engine StopCLIP, Wire Harness CLIP, TubeFlywheel Assy KEY, Special Woodruff FAN, CoolingFlywheel Comp NUT, Special 16MMMuffler Assy PIPE, EX MufflerPROTECTOR, Muffler PROTECTOR, EX. PipeFuel Tank Assy GASKET, Fuel Filler CAP Rubber Supporter 107MMJOINT, Fuel Tank Tank COMP., Fuel *NH1*, BlackIgnition Coil Assy CAP ASSY., Noise Suppressor GROMMET, WireWIRE, Stop Switch 370MM Coil ASSY., IgnitionPiston Assy PISTON, Standard BOLT, Connecting RODRing SET, PISTON, STD Ring SET, PISTON, 0.75, OptionalRecoil Starter Assy SPRING, Starter Return PULLEY, Recoil StarterRATCHET, Starter SPRING, FrictionGear Reduction Assy Shim a Optional GEAR, Primary Drive 17TCountershaft SHAFT, P.T.O. H- TypeLabel Assy LABEL, Caution Labels AssyEMBLEM, Internal MARK, CAUTION, ExternalTerms and Conditions of Sale Stow Construction Equipment Page HERE’S HOW to GET Help
Top Page Image Contents