Effects Loop, Speaker Outputs, Ground Lift

Rear Panel

23EFFECTS LOOP

1/4" Send and Return jacks for the effects loop.

24CABINET IMPEDANCE SELECTOR SWITCH

This three-position switch allows appropriate selection of speaker cabinet impedance. If two loudspeaker enclosures of equal impedance are used, the switch should be set to half the individual value. For example, two 16-ohm enclosures necessitate an 8-ohm setting, while two 8-ohm enclosures would require a 4-ohm setting. Minimum speaker impedance is 4 ohms. The stock setting for the internal speaker is 16 ohms.

25SPEAKER OUTPUTS

These paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Again, minimum speaker impedance is 4 ohms. The CABINET IMPEDANCE SWITCH (24) should be set to match the load of the speaker cabinet(s).

26MSDI™

Microphone Simulated Direct Interface. Peavey's exclusive MSDI simulates the sound of a microphone placed approximately 8" from loudspeaker cone, allowing the user to send a clean signal to the mixing console. This is a non-powered output and safe for use with any mixing console.

27GROUND LIFT

Engage this switch if the mix engineer is hearing a hum in the MSDI output This should eliminate the hum.

28FOOTSWITCH

1/4" input for the optional footswitch.

29FUSE

A fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same type and value to avoid damaging the ampliﬁer and voiding the warranty. If the amp repeatedly blows the fuse, it

should be taken to a qualiﬁed service center for repair.

WARNING: THE FUSE SHOULD ONLY BE REPLACED AFTER THE POWER CORD HAS BEEN DISCONNECTED.

30IEC MAINS CONNECTOR

This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included in the carton. The mains cord should be connected to the ampliﬁer before connecting to a suitable AC outlet.

U.S DOMESTIC AC MAINS CORD

The mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plug with ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly.

Never break off the ground pin on any equipment. It is provided for your safety.

NOTE: FOR UK ONLY

If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the Earth symbol, colored green, or colored green and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

6505 +112 Combo specifications

The Peavey 6505 +112 Combo is a powerful and revered amplifier in the world of rock and metal music. Known for its high gain and aggressive tone, this combo amp has become a staple for guitarists seeking both versatility and reliability. It delivers the renowned Peavey 6505 sound in a more portable package without sacrificing quality or performance.

At the heart of the 6505 +112 Combo is its all-tube design, powered by two 6L6GC power tubes and three 12AX7 preamp tubes. This arrangement produces an impressive 60 watts of power, allowing for an explosive sound that's ideal for live performances and studio recordings alike. The dynamic range and rich harmonic overtones are key to its popularity among heavy genres, providing a thick, saturated tone that can cut through any mix.

One significant feature of the 6505 +112 Combo is its dual-channel operation, comprising a clean channel and a lead channel. The clean channel offers a warm, articulate sound, suitable for a variety of styles, while the lead channel unleashes the amp's famous high-gain characteristics. Each channel is equipped with its own set of controls, including gain, bass, mid, treble, and reverb, allowing for extensive tonal shaping.

The amp also includes a built-in reverb effect, which adds depth and ambiance to the sound, enhancing overall playability. Another notable aspect is the presence and resonance controls, providing further customization over bass response and high-frequency harmonics. These features make the 6505 +112 Combo not only suitable for versatile genres but also for amplifying distinct personal tones.

Featuring a single 12-inch Sheffield speaker, the 6505 +112 Combo delivers a focused sound that excels in both projection and clarity. The sturdy construction ensures durability, making it the perfect companion for touring musicians. Additionally, its lightweight design compared to traditional amp stacks allows for easier transport without compromising sound quality.

Incorporating Peavey’s patented technology, the 6505 +112 Combo stands out with its reliability and performance consistency even under demanding conditions. Whether used for practice, recording, or live gigs, this amplifier offers an exceptional combination of power, tone, and versatility, solidifying its place in the hearts of guitarists around the world. The Peavey 6505 +112 Combo is a prime example of how well-crafted engineering can meet the needs of modern musicians, making it a go-to choice in high-gain amplification.