Fostex FD-4 Play button Play, Stop button Stop, Record button RECORD/ Auto Punch, Shift key Shift

Page 14

Names and Functions

25. Play button [PLAY]

Pressing this button causes the recorder section to play back. Pressing this button while holding down the RECORD button when a track is in READY mode will cause the FD-4 to start recording on the READY track.

Pressing only this button during the recording operation will punch-out (cancel) recording. Pressing this button while holding down the STOP button will cause the “CLIPBOARD PLAY” operation to start.

*Refer to the “STOP button” section and page 57 for more information on the “CLIPBOARD PLAY” operation.

*Refer to page 48 for more information on the Punch Out operation using the PLAY button.

26.Stop button [STOP]

Pressing this button during the playback, recording, fast forward, or rewind operation will stop the recorder transport operation. Pressing this button while the FD-4 is in SETUP mode will cause the unit to exit SETUP mode.

Pressing the PLAY, REWIND, or F FWD button while holding down the STOP button will cause the following operations to start.

If you wish to rehearse the Manual Punch In/Out operation using the foot switch, press the foot switch while holding down this button to enter Rehearsal mode.

PLAY

“CLIPBOARD PLAY” operation starts. (See

 

 

below.) . During the operation, the STOP

 

LED flashes and the PLAY LED lights up.

*Refer to pages 57 and 66 for more information on these operations.

* Refer to page 46 for more information on the Punch In/Out

operation using a foot switch.

27. Record button [RECORD/ AUTO PUNCH ]

Pressing the PLAY button while holding down this button will cause the FD-4 to start recording on any READY tracks. At this time, the flashing LED of the RECORD TRACK select key for the corresponding READY track lights up steadily, and the PLAY LED and the RECORD LED light up.

If you press only the RECORD button, a READY Real track enters input monitoring mode (The RECORD LED flashes.). At this time, pressing the RECORD button again will cancel the input monitoring mode, and the track will return to playback monitoring mode.

Pressing the RECORD button while holding down the SHIFT key will toggle between AUTO PUNCH on and off.

*Refer to page 28 for more information on recording.

*Refer to page 43 for more information on AUTO PUNCH mode.

*Refer to page 26 for more information on input monitoring and playback monitoring.

28.Shift key [ SHIFT ]

Press a key, button, or turn the dial while holding down the SHIFT key to activate the following “shift-invoked” functions.

STOP

REWIND

ABS 0 is located. (See below.)

F FWD

REC END is located. (See below.)

* CLIPBOARD PLAY operation

The CLIPBOARD PLAY operation plays back data on the clipboard. (If the clipboard does not contain any data, the display shows [Void Data !] and nothing happens.). During this operation, the display indicates the type of the data (“Copy Clip” for copy data, and “Move Clip” for move data), and the duration. The indicator of the copy source or move source track flashes.

You can audition the data at edit points (locate points) stored in the memory keys. (For more information, refer to “Preview function” on page 69.)

 

 

RECORD TRACK

 

 

1/L

2/R

3/L

4/R

L

R

 

 

 

 

ADD. TRACK

 

 

PREVIEW

 

 

START

IN

OUT

END

IN

OUT

 

AUTO PUNCH

 

CLIPBOARD

 

AUTO RTN

 

 

 

 

 

 

UNDO/

 

 

HOLD/

STORE

EDIT

REDO

 

 

PGM SEL

 

 

 

 

 

VARI

AUTO RTN

 

 

 

 

PITCH

AUTO PLAY

LOCATE

 

 

SHIFT

P. EDIT

 

LOC MEM

 

 

 

 

CLIPBOARD PLAY

 

 

AUTO

 

LOCATE ABS 0

 

 

PUNCH

 

LOCATE REC END

 

 

RECORD

 

STOP

PLAY

REWIND

F FWD

The removable SCSI disk is

ejected. (Refer to “Recording

Preparation” on page 7.)

 

 

TIME BASE

DISP SEL

SETUP

SEL

EXECUTE EXIT

/YES /NO

ELECT

ACCESS

JOG SHUTTLE

In this way, you will know which track the currently playing data comes from and why the data is on the clipboard.

* ABS 0 locate operation

This operation locates the beginning of the current Program (ABS time: 00m 00s 00f).

* REC END locate operation

This operation locates the end of the audio recording (REC END) on the Real track in the current Program.

Auto Punch mode is turned on and off. (Refer to “Punch In/Out” on page 43.)

You can edit Vari Pitch data. (Refer to “Playback in Vari Pitch mode” on page 40 for more information.)

You can edit locate data stored in the LOCATE key. (Refer to “Storing an edit point (locate point)” on page 63 for more information.

The SHUTTLE dial function is activated. (Refer to “JOG dial/

SHUTTLE dial cueing” on page 62 for more information.)

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Safety Instructions Introduction Main features Recording PreparationMixer section Recorder sectionAbout damages Connecting a Scsi driveRecording Preparation About copyrightsInsert a disk into the Scsi drive Recording modeFormatting a new disk Press the EXECUTE/YES keyRemoving a disk from the Scsi drive Turn the JOG dial to select a recording modeWhen you format a disk, a Program is named temporary title Press the Stop button or the EXIT/NO keyFormatting the disk again Press the Setup keyUse the JOG dial to select a recording mode Press the EXECUTE/YES key againControl panel Names and FunctionsRear panel Front panelPanpot knobs PAN L/R Input select switches Input SEL INPUT/OFF/TRKInput faders Monitor panpot knobs PAN MON L/MON R Equalizer control knobs EQ HIGH/MID/LOW Input level switches Level H/M/L Monitor level control knob MON INPUT/TRK AUX send knobs AUX AUX 1/AUXContrast adjustment knob LCDDisplay indication select key Setup key SetupAccess LED Access Time Base select keyRecord button RECORD/ Auto Punch Play button PlayStop button Stop Shift key ShiftLocate key LOCATE/ LOC MEM Auto Return/Auto Play mode on/off keyVari Pitch key Vari PITCH/ P.EDIT Hold/ key HoldEdit key Edit Store key StoreUndo/Redo key UNDO/REDO Auto Return Start keyAuto Punch Out key Auto Return End key Auto RTN END/ PreviewAuto Punch In key Auto Punch IN/ Preview Clipboard In key Clipboard IN/ PreviewStereo Out jacks ST. OUT L, R Connector RCA pin Input jacks 1, 2, 3, 4 Connector phoneMonitor Out jacks MON OUT L, R Connector RCA pin Headphone jack Phones Connector stereo TRS phoneMidi in jack Midi in Connector DIN 5-pin Balanced input connectors 3, 4 Input 3Midi OUT jack Midi OUT Connector DIN 5-pin AUX Send jacks 1, 2 AUX Send 1Power cable Data output jack Data OUT Connector OpticalData input jack Data in Connector Optical Power switch PowerTime Base is MTC Time Base is ABSTime Base is BAR/BEAT/CLK Time Base is BAR/BEAT/CLK Time Base is MTCTime Base is ABS Disk recordable remaining Time is displayedVoid Out message Void Data messageAction to take Track unselected messageBefore Starting Time BaseArea actually used on the disk Remain indicatorRecording method Playback monitoring Real track and Additional trackInput monitoring REC SEL switch PAN knobs and stereo busConnecting the guitar and the monitoring head- phones FD-4 initial settingsSetting the disk Initial settingsMonitoring the recording signal Setting the switch and knobAdjusting the recording level Starting recordingUndo/Redo recording Recording onto the additional trackPlayback of the additional track sound Checking the recording soundPlaying track Undo/redo subsequent to exchangeRecording a drum machine to track Connecting a sound sourceBasic Multitrack Recording Overdubbing the bass to trackListening to the overdubbed sound Undo/redo overdubbingMixdown Settings for overdubbing the electric guitar to trackSettings for overdubbing the vocal to track AUX SEND2 and AUX RTN2 of the FD-4 respectivelySettings for the effect units Setting the switch and knob on the FD-4Setting the output level and the master recorder MixdownTo enter a title Handling ProgramsCreating a new Program Using the Program Change function Press the Setup key while the FD-4 is stopped Deleting a ProgramEditing a Program title After you enter the title, press the EXECUTE/YES keyAfter you set the pitch data, press the EXIT/NO key Playback in Vari Pitch ModeSet the desired pitch data using the JOG dial Creating a Tempo Map Connecting a sound source and a effect unitRecording to a Metronome Sound Turning the Metronome function onChecking the recorded sound Checking the metronome soundQuitting recording Press the Stop button to stop the recorderAuto Punch In/Out What is Punch In/Out recording?Punch In/Out Recording Storing the edit pointsPreparation Connecting the instrumentSetting the mixer section Tips for rehearsalHint Quick and easy operation for repeated rehearsal Control panel settings are the same as those for rehearsalAuto Punch In/Out Take Press the Record Track select key 3/L to set track 3 toConnecting the instrument and a foot switch Manual Punch In/OutManual Punch In/Out take Cancelling Rehearsal modeRehearsing Punch In/Out recording HintUndo/Redo Manual Punch In/Out recording Ping-Pong Recording Connecting effect unitsAdjusting the recording level/rehearsal Quitting ping-pong recording Undo/Redo ping-pong recordingPerforming ping-pong recording Checking the ping-pong recording resultsConnect effect units to Aux sends/returns Set the channel 1-4 Input SEL switches to TRKChecking the result of ping-pong recording Digital Recording Setting a recording trackConnecting an external digital device Selecting a Program to recordSetting a digital output track You cannot assign the same track to L and RDigital mixdown Assigning output tracksHow to use the Recorder in jack Edit functions Editing TracksCopy & Paste and Move & Paste Copy & PasteExecuting Copy or Move Checking and adjusting the edit pointsChecking the clipboard data Executing PastePress the Stop button or the EXIT/NO key EraseUndo/Redo Paste Erasing a specified part of the data between ABS 0Executing Erase Undo/Redo Erase Point is passed in the Play or Record modeTrack Exchange Swapping data between Real tracks mono track dataSelecting Additional tracks L-R and Real tracks Executing Track ExchangeSwapping mono track data Select the tracks to swap dataCue & Review Function Cue & Review function using the Rewind and F FWD buttonsDigital scrubbing using the JOG dial Press the Store key Storing a Locate Point Edit PointStoring in real-time Press the desired memory keyPress the HOLD/ key while the FD-4 is stopped Editing and storing locate dataEditing and storing data Press the memory key that you pressed in againEditing the data stored in the Locate key Auto Play Locate FunctionDirect Locate Executing the Auto Play functionPress the Locate key Auto ReturnExecuting the Auto Return function Store the Auto RTN Start and Auto RTN END pointsAuto Repeat operation Auto RepeatExecuting the Auto Repeat function Start playback a little before the Auto RTN Start pointPreviewing the fall of the sound fade out Preview FunctionPreviewing the rise of the sound fade CLK BAR Trim the position at the selected unit digitTime Base Midi Synchronization Midi clock sync systemMTC sync/Machine Control system Connecting an external deviceRefer to page 86 for more information on Setup mode See page 92 for more informationSetting the device ID number Setting MTC OffsetSetting a frame rate Checking synchronization and Machine ControlSetting the FD-4 Sync system in Slave modeSetting up the external device Checking the chase and lock operationRecording Outline of the save/load operation Connecting a DAT machineSaving and Loading Song Data Saving from FD-4 to DAT Loading from DAT to FD-4Preparing a DAT machine Remember thisSaving song data Operation on the FD-4Use the JOG dial to select the desired Program Select the tracks to save using the JOG dialUse the JOG dial to display Save PGM ? Loading song data Press the Setup key when the FD-4 is stoppedSelect tracks to load using the JOG dial You can monitor the data using the following methods Start playing the DAT machineExecution menu Selecting Setup modeChanging the initial settings menus Modifying or deleting stored time signatures Setting a time signatureStoring a time signature Select a Program for which to set a time signatureChecking the stored tempo setting Setting a tempoClearing all time signature and tempo settings Storing a tempo valueModifying or deleting stored tempo settings Repeat steps 3-5 to store necessary tempo dataSetting the Metronome function Setting the Metronome functionSetting a preroll value Setting a preroll timeTurn the JOG dial to select the desired Midi sync signal Setting Midi sync output signalSetting Midi sync signal Initial setting CLK clock & Song Position PointerSetting an MTC frame rate Setting an MTC frame rateSetting an MTC offset value Setting an MTC offsetSetting MTC Offset mode Setting Offset modeSetting the Slave mode Use the JOG dial to select the desired Offset modeSetting the Slave type external sync signal Setting the Slave typeTurning Slave mode on and off Use the JOG dial to turn Slave mode on and offUse the JOG dial to enable or disable recording Setting the Record Protect functionRecording enabled/disabled Setting digital input tracks Setting digital input tracksSetting digital output tracks Setting digital output tracksSetting BAR/BEAT resolution mode Setting BAR/BEAT resolution modeUse the JOG dial to turn the mode on or off Setting the Midi device numberSetting the Midi device ID Use the JOG dial to set the desired Midi device ID numberMidi Implementation Chart Date Version FunctionMMC Command List Refer to MMC Response/Information Field ListCleaning the exterior MaintenanceSpecifications Block Diagram Declaration of EC Directive Index Fostex Corporation
Top Page Image Contents