Fostex FD-4 owner manual Vari Pitch key Vari PITCH/ P.EDIT, Auto Return/Auto Play mode on/off key

29.Vari Pitch key [VARI PITCH/ P.EDIT ]

This key toggles Vari Pitch mode on and off. When Vari Pitch mode is on, the “VARI PITCH” indicator lights up on the display, and the FD-4 plays using the current pitch data. Pressing the VARI PITCH key while holding down the SHIFT key will cause the FD-4 to enter edit mode, in which you can change pitch data in real-time.

To exit edit mode, press the EXIT/NO key.

Refer to page 40 for more information on playing with Vari

Pitch and editing Vari Pitch data.

30.Auto Return/Auto Play mode on/off key

[AUTO RTN/AUTO PLAY]

Use this key to turn on and off Auto Return mode, Auto Play mode, and Auto Repeat mode. Each time you press the key, the mode will change and the following indication will be displayed.

			Auto Return/Play mode is OFF.
	AUTO
			(No indication)
			Auto Play mode is ON.
	AUTO
PLAY			(“PLAY” lights up.)
			Auto Return mode is ON.
	AUTO
		RTN	(“RTN” lights up.)
			Auto Repeat mode is ON.
	AUTO
PLAY		RTN	(Both “PLAY” and “RTN” light up.)

* Auto Play mode

The FD-4 locates a point and starts playing from the locate point.

* Auto Return mode

When the AUTO RTN END point is reached while the recorder section is playing, the FD-4 automatically locates the AUTO RTN START point.

This mode is effective only if the AUTO RTN START point and the AUTO RTN END point have already been specified.

<Note>

The Auto Return function is enabled only when the FD-4 is playing. While the FD-4 is recording, the FD-4 will not locate the START point after it reaches the AUTO RTN END point.

*Auto Repeat mode

This mode is effective only when Auto Play mode and Auto Return mode are turned on. The FD-4 will play the part between the AUTO RTN START point and the AUTO RTN END point repeatedly. This mode is also effective only if the AUTO RTN START point and the AUTO RTN END point have already been specified.

Refer to page 66 for more information on each mode.

Names and Functions

31. Locate key [LOCATE/ LOC MEM ]

Use this key to locate a point. Press a key that stores locate points, such as the CLIPBOARD IN/OUT keys, AUTO PUNCH IN/OUT keys, and AUTO RTN START/END keys, then press the LOCATE key to locate a point stored in the corresponding key.

The last locate data will replace the data stored in the LOCATE key. Therefore, pressing only the LOCATE key will locate the last locate point. If you have set Auto Play mode, the FD-4 will start playing from the located point.

Pressing the LOCATE key while holding down the SHIFT key will cause the FD-4 to enter edit mode, in which you can edit data stored in the LOCATE key.

Refer to page 66 for more information on the Locate function.

Refer to page 63 for more information on editing data using the LOCATE key.

32. Hold/> key [HOLD/>]

Pressing the HOLD/> key while the recorder is operating will cause the FD-4 to capture the time at which you pressed the key (or bar/beat/clock value), display it, then enter edit mode. (If you press the HOLD/> key while the recorder section is stopped, the FD-4 enters edit mode directly.)

To cancel edit mode, press the STOP button, DISP SEL key, or the EXIT/NO key.

In edit mode, you can use this key to select a digit of the value to edit (edit point). You can select a digit which flashes on the display) in the following order.

ABS or MTC is used as Time Base:

First, “S” (second) flashes. Each time you press the HOLD/> key, the flashing characters change in this order: F -> SF -> H -> M-> S.

BAR/BEAT/CLK is used as Time Base:

First, “BAR” flashes. Each time you press the HOLD/> key, the flashing indicator changes in this order: -> CLK -> BAR.

If you press the HOLD/> key and the STORE key simultaneously while the recorder is stopped, the FD-4 enters Program Select mode, in which you can select a Program or set up a new Program.

Refer to page 63 for more information on editing memory.

Refer to page 37 for more information on the Program Select function.

15