Nilfisk-ALTO DJM-3 user manual AC Inlet and Fuse Holder, Uk/Aust

Page 12

3.3.The Rear Panel

UK/AUST

USA / Canada

 

 

210-240V 50Hz

100-120V

60Hz

 

 

Fuse:T200mAL

Fuse:T400mAL

 

 

 

 

CAUTION

 

 

AC INPUT

 

RISK OF ELECTRIC SHOCK

 

MODEL

 

DO NOT OPEN

 

EUROPE

 

WARNING: SHOCK HAZARD - DO NOT OPEN

 

 

210-240V

50Hz

AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

 

Fuse:T200mAL

 

 

 

RATED POWER CONSUMPTION: 12W

 

 

Apparaten skall anslutas till

 

 

Jordat uttag nar den ansluts

MAIN

TAPE

Till ett natverk

 

 

 

 

fuse 250V a with only Use

POWER

 

 

 

 

ON

 

 

 

 

OFF

MAIN OUT

 

 

 

SERIAL

 

 

GND

GND

SEND

RETURN

 

 

FROM PFL

TO MAIN

LINE PHONO

LINE PHONO

 

 

L

 

 

 

R

 

EFFECTS

INPUT 2

INPUT 1

 

 

PHONO

PHONO

 

 

LINE

LINE

27

28

29

30

31

32

3.3.1 AC Inlet and Fuse Holder

27

The fuse holder position (please follow the triangle that indicated the voltage accepted by the unit) can be changed only by a qualified Engineer. Please check the Voltage accepted by the unit and the Voltage available from your AC sockets before connecting the unit to the Mains.

3.3.2 POWER Switch

28

This switch turns the Mixer ON and OFF.

3.3.3 MAIN OUT

29

Both MAIN output and TAPE output are RCA types connectors. Yes the same largely used in hi-fi and are low impedance. Through the MAIN output you can connect your DJM 3 to an amplifier. Through the TAPE output you can connect your DJM 3 to a tape recorder.

3.3.4 EFFECTS send and return

30

You can send the PFL (pre fader level) signal through the SEND sockets to a signal processor such as reverb, equaliser, etc. Then from the same effect unit you bring the signal back into the DJM 3 via the RETURN sockets and the audio signal is routed into the MAIN output.

3.3.5 INPUT

31

-PHONO input: Both Channels feature PHONO inputs including RIIA preamplifier for turntable. PIN (RCA) jacks shall be used to connect the turntable.

-LINE input: Through these RCA type sockets you can connect a CD player, an MD player or any other high level device such as Tape Recorder, DAT, etc,

Important Notice: If you wish to connect LINE level devices into the LINE/PHONO input, make sure that the LINE/ PHONO switch is on LINE position otherwise the sensitive RIAA preamplifier built-in in the Phono input will be overloaded and will produce distortion.

3.3.6 GND screw

32

This grounding connection is provided for your turntables.

10

Image 12
Contents DJM-3 Page Safety Related Symbols Important Safety InstructionsPower Supply External ConnectionPreface Table of Contents Introduction Control Elements 3.1 The TOP Cover Channel Section PHONO-LINE to Line switch Gain controlEqualizer control Program FaderSurround on switch Mode switchMAIN/PFL switch Main OUT Section Level controlBeat Assist switch Tempo DisplayTempo Difference Led segment Time Offset Led segmentMIC in Jack AC Inlet and Fuse Holder UK/AUSTTechnical Specifications InputsSystem Block Diagram Warranty Warranty Registration CardSeikaku Technical Group Limited