Multiquip manual MT-76D2TAMPING Rammer Safety Message Alert Symbols, Hazard Symbols

Page 6

MT-76D2TAMPING RAMMER — SAFETY MESSAGE ALERT SYMBOLS

FORYOUR SAFETY AND THE SAFETY OF OTHERS!

HAZARD SYMBOLS

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Owner's Manual has been developed to provide complete instructions for the safe and efficient

NOTE operation of the MQ Mikasa Model MT-76D2 Tamping Rammer. Refer to the engine manufacturer's instructions for data relative to its safe operation.

Before using this rammer, ensure that the operating individual has read and understood all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER,

DANGER

You WILL be KILLED or SERIOUSLY INJURED

if you DO NOT follow these directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if you DO NOT follow these directions.

CAUTION

You CAN be INJURED if you DO NOT follow these directions.

Potential hazards associated with the operation of a MT-76D2Tamping Rammer will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

WARNING Lethal Exhaust Gas Hazards

Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.

WARNING Explosive Fuel Hazards

Fuel is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids.

DO NOT fill the fuel tank while the engine is running or hot. DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. Store fuel in approved containers, in well-ventilated areas and away from sparks and flames.

 

WARNING

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. Never operate the engine with heat shields or heat guards removed.

 

WARNING

Respiratory Hazards

ALWAYS wear approved respiratory protection when required.

PAGE 6 — MT-76D2 TAMPING RAMMER — OPERATION AND PARTS MANUAL — REV. #5 (11/08/07)

Image 6
Contents Model MT-76D2 MT-76D2 Tamping Rammer Proposition 65WARNING Page MT-76D2 Tamping Rammer -TABLE of Contents Mikasa MT-76D2Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only MT-76D2TAMPING Rammer Safety Message Alert Symbols Hazard SymbolsMT-76D2TAMPING Rammer Safety Message Alert Symbols Rotating Parts HazardsMT-76D2TAMPING Rammer Rules for Safe Operation Read this manualMT-76D2TAMPING Rammer Rules for Safe Operation TransportingMT-76D2TAMPING Rammer Operation and Safety Decals Construction of Tamping Rammer MT-76D2TAMPING Rammer General InformationDefinition of Tamping Rammer Rammer Gearbox and Spring CylinderMT-76D2TAMPING Rammer Specifications MT-76D2 Rammer SpecificationsMT-76D2TAMPING Rammer Controls and Components MT-76D2 Tamping RammerMT-76D2TAMPING Rammer Basic Engine MT-76D2TAMPING Rammer Initial START-UP EngineStarting Throttle LeverMT-76D2TAMPING Rammer Operation OperationStopping the Engine Replacement of Lubricant Engine Engine Oil Replacement IntervalDaily Transportation MT-76D2TAMPING Rammer MaintenanceCleaning the Air Cleaner StorageMT-76D2TAMPING Rammer Troubleshooting Engine TroubleshootingRammer Troubleshooting Part NO. Column Explanation of Code in Remarks ColumnNO. Column QTY. ColumnMT-76D2TAMPING Rammer Suggested Spare Parts MT-76D2 Rammer withYanmar L48V6 EngineMT-76D2TAMPING Rammer Name Plate and Decals Name Plate and DecalsMT-76D2TAMPING Rammer Nameplate and Decals MT-76D2TAMPING Rammer Crank Case and Engine Assy Crankcase and Engine AssySEAT, AIR Cleaner Connecting RODPACKING, AIR Cleaner CrankcaseMT-76D2TAMPING Rammer Crankcase and Engine Assy MT-76D2TAMPING Rammer Crankcase and Engine Assy MT-76D2TAMPING Rammer Cylinder Guide and Foot Assy Cylinder Guide and Foot AssyMT-76D2TAMPING Rammer Cylinder Guide and Foot Assy MT-76D2TAMPING Rammer -TANK and Handle Assy Tank and Handle AssyPart Name QTY Remarks Yanmar L-48V6 Engine Cylinder Block Assy Cylinder Block AssyNeedle Bearing Starter CoverBolt M10X 12 Plated Bolt M 8X 12 PlatedYanmar L-48V6 Engine Cylinder Head Assy Cylinder Head AssySuction Valve Valve ADJUST. ScrewCylinder Head Exhaust ValveYanmar L-48V6 Engine Crankshaft and Camshaft Assy Crankshaft and Camshaft AssyYanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Piston Assy Piston AssyPiston Ring SET OS=0.50 Piston Ring SET STDPiston Ring SET OS=0.25 CirclipYanmar L-48V6 Engine LUB. OIL Pump and Governor Assy LUB. OIL Pump and Governor AssyYanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Yanmar L-48V6 Engine Cooling and Starting Assy Cooling and Starting AssyBolt M 6X12 Plated Cooling & Starting Device AssyCylinder Cover Cooling FAN CaseYanmar L-48V6 Engine Fuel Injection Pump Assy Fuel Injection Pump AssyDelivery Valve Spring Fuel Injection Pump BodyValve ASSY. Delivery P. Delivery HolderYanmar L-48V6 Engine AIR Cleaner Assy AIR Cleaner AssyAIR Intake Pipe AIR Intake GasketStud M 6X14 Plated Yanmar L-48V6 Engine Muffler Assy Muffler AssyBolt M 6X14 Plated Muffler GasketMuffler ASSY., DRM Bolt M 6X18 PlatedYanmar L-48V6 Engine TOOLS, Labels and Gasket SET Assy TOOLS, Labels and Gasket SET AssyDiesel Label AIR Cleaner GasketYanmar Label Tool BAGYanmar L-48V6 Engine Accessories Assy Accessories AssyFuel OIL Pipe Hose 12.5 BandPiece Rubber HoseTerms and Conditions of Sale Parts Freight PolicyPage Heres HOW to GET Help