Listings and Code Approvals

The BF series fireplaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for fixed and location-dedicated electric room heaters.

MODEL SPECIFICATIONS

Model				Remote	Wall	Refractory	AMPS	AMPS	AMPS	AMPS
	Description	Voltage Volts	Rated Power Watts				No Heat	120	208	240
Number				Control	Thermostat	Brick Look
							120 Volt	Volt	Volt	Volt

BF33ST	33”	120/120/208/	245/1440/2100/	Option	Option	N/A	2.0	12.0	10.10	11.25
	Standard	240	2700

BF33DX	33” Deluxe	120/120/208/	245/1440/2100/	Option	Option	Included	2.0	12.0	10.10	11.25
		240	2700

BF39ST	39”	120/120/208/	245/1440/2100/	Option	Option	N/A	2.0	12.0	10.10	11.25
	Standard	240	2700

BF39DX	39” Deluxe	120/120/208	245/1440/2100/	Option	Option	Included	2.0	12.0	10.10	11.25
		/240	2700

BF45ST	45”	120/120/208/	245/1440/2100/	Option	Option	N/A	2.0	12.0	10.10	11.25
	Standard	240	2700

BF45DX	45” Deluxe	120/120/208/	245/1440/2100/	Option	Option	Included	2.0	12.0	10.10	11.25
		240	2700

NOTE: Power ratings shown include the light bulbs and motors (275 watts)

WARNING

The installation of the fireplace unit must comply with the applicable Local and/or National Electrical Codes and utility requirements. This installation should be entrusted to duly qualified personnel where required by law.

STEP-BY-STEP INSTALLATION (Note: Please read all instructions before installing)

1.Rough in framing opening following the recommended dimensions located in (Section A: Framing).

2.Allow 8” of service cable for connecting power supply wire to junction box on fireplace when installing before finishing wall. Allow up to 4 feet of service cable for connecting power supply wire to junction box on fireplace when installing after finishing wall.

Remove the outer jacket and strip the individual conductors ½” from the end.

3.Loosen the screw securing the junction box cover and remove the cover.

4.Remove knockouts if necessary or use the provided cable clamp.

5.Place unit in position in the framed opening, level with shims if necessary and attach unit to frame using mounting flanges provided (see figure 3 on page 3).

6.Unit is factory wired for 208/240 volt power supply (see figure 1 on page 3). If 120 volt operation is required, slide the switch and reconfigure the wiring

(see figure 2 on page 3). Wires L1, L2, N & G are attached to the rear of the junction box cable clamp for easy access.

Note

If wiring unit to operate with NO heat a dedicated circuit may not be required.

7.Wire a dedicated, properly fused circuit with a 15amp rating for the appropriate voltage (120, 208/240). (see Section C for factory setting wiring)

8.Make wall switch and or wall mounted thermostat connections as outlined in Section D: Wiring.

9.Place all connectors inside the unit and secure the junction box cover to unit. Ensure that the cable clamp grips only the jacket of service cable, thermostat and if applicable wall switch lines.

BF33ST/DX, BF39ST/DX specifications

The Dimplex BF39ST/DX and BF33ST/DX electric fires are innovative heating solutions that combine stylish design with advanced technology. Both models are part of Dimplex's extensive range of electric fires, designed to offer both functionality and aesthetic appeal, making them ideal for modern homes.

The BF39ST/DX model features a larger viewing area with a 39-inch width, while the BF33ST/DX offers a slightly smaller 33-inch width. This provides homeowners with flexibility when selecting the right size for their living spaces. Both models are designed to fit seamlessly into any room, offering a contemporary and appealing look that enhances the existing décor.

One of the standout features of these electric fires is the realistic 3D flame effect, Dimplex's patented Opti-myst technology. This advanced technology creates a lifelike flame and smoke effect using water vapor, providing an ambiance that closely resembles that of a traditional wood-burning fire. The flames can be adjusted for intensity, allowing users to customize the experience according to their preferences.

In terms of heating efficiency, both the BF39ST/DX and BF33ST/DX come with a 2kW fan heater that allows for rapid warming of spaces. Users can choose between two heat settings, enabling efficient temperature control and energy savings. This feature is particularly useful during colder months when immediate warmth is a priority.

Both models are equipped with a remote control, providing convenience for users to adjust settings from the comfort of their seat. This feature includes a timer function, allowing users to set the fire to operate for a specific duration or program it to turn off automatically.

Safety is paramount, and Dimplex has integrated essential safety features into both models. The fires are designed with an auto shut-off function that activates if the heater overheats, ensuring peace of mind for users.

Another notable characteristic is the ease of installation. The BF39ST/DX and BF33ST/DX can be wall-mounted or inset, providing flexibility in installation options to suit various home layouts. Their lightweight design simplifies repositioning, making it easy to change the fire's location if desired.

In summary, the Dimplex BF39ST/DX and BF33ST/DX electric fires offer a perfect blend of modern design, advanced heating technology, and user-friendly features. With their realistic flame effects, efficient heating, safety mechanisms, and flexibility in installation, these electric fires are an excellent heating solution for any contemporary living space.