Desa (V)K36EP SERIES, (V)K36EN SERIES Vertical Termination Configurations, Vertical Venting

Page 13

Venting Installation

instructions

Continued

Vertical Termination Configurations

Figures 21 through 24 show four different configurations for verti- cal termination.

Venting with Two 90° Elbows

Vertical (V)

Horizontal (H1) +

 

Horizontal (H2)

5' min.

2' max.

6' min.

4' max.

7' min.

6' max.

8' min.

8' max.

20' max.

8' max.

45° Elbow

Venting with Two 90° Elbows

Vertical (V1)

Horizontal (H)

5' min.

6' max.

6' min.

12' max.

7' min.

18' max.

8' min.

20' max.

Note: Install restrictor into inner collar of

fireplace as shown.

45° Elbow

Note: Vertical (V1) + Vertical (V2) = 40' max.

Figure 23 - Vertical Venting Configuration Using Two 90° Elbows (Vertical Round High Wind Termination Shown)

Note: Install restrictor into inner collar of fireplace as shown.

Figure 21 - Vertical Venting Configuration Using Two 90°

Elbows with Two Horizontal Runs (Vertical Round High Wind

Termination Shown)

 

Venting with One 90° Elbow

 

Vertical (V)

Horizontal (H)

 

5' min.

2' max.

 

6' min.

4' max.

 

7' min.

6' max.

 

8' min.

8' max.

45° Elbow

20' max.

8' max.

45° Elbow

Note: Install restrictor into inner collar of fireplace as shown.

Vertical Venting

V = 40' max.

Note: Install restrictor into inner collar of fireplace as shown.

Figure 22 - Vertical Venting Configuration Using One 90°

Figure 24 - Vertical Venting Configuration With No Horizontal

Elbow (Vertical Round High Wind Termination Shown)

Run (Vertical Round High Wind Termination Shown)

111924-01D

www.desatech.com

13

Image 13
Contents What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsProduct Identification Product FeaturesLocal Codes Location and space requirements Pre-Installation PreparationClearances Framing and finishing Framing Clearances for Installation Against an Exterior WallTermination CAP AIR Supply Inlet GAS Meter Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Horizontal Termination InstallationVent Pipe Connections Vent pipe before connecting horizontal run to vent cap see Ground Floor Installation Horizontal Termination ConfigurationsVenting with Two 90 Elbows Snorkel Termination InstallationOffset with Wall Strap and 45 Elbows Flat Ceiling InstallationVertical Venting Vertical Termination ConfigurationsHigh Altitude Installation Fireplace InstallationParts lists for venting kits and components Installing optional blower accessoriesAttaching Speed Control to Firebox Model BKT InstallationBlower Wiring Diagram Installing Gas Piping to Fireplace LocationInstallation Items Needed Installation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Gas Supply Piping System Checking GAS ConnectionsRemoving/Replacing Glass Door Pressure Testing Fireplace Gas ConnectionsRemoving Louver Panels Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPaCleaning Glass Door Installing Optional Brick liner Models BL36DASA, BL36DHASAUnplug fireplace. Let cool before installing brick liner Removing Glass DoorWall Switch Installation Installing logs, lava rock and glowing embersOptional Remote control Installation model WRC Line Wiring DiagramTo Turn OFF GAS Operating FireplaceOptional Remote Operation Pilot assembly Cleaning MaintenanceInspecting Burners Burner Flame PatternLogs Pilot and burnersVenting system To clean pilot. This can damage pilot unit TroubleshootingTop above Gas leak. See Warning statement atService Hints Replacement PartsTechnical Service SpecificationsModels VK36EN, VK36ENH, Vk36ep and vk36eph Illustrated Parts BreakdownParts Available not Shown Parts ListBurner Assembly Models VK36EN, VK36ENH, Vk36ep and vk36eph Parts List Accessories 111924-01D Keep this Warrant Warranty Information