General Instructions, General Information

GENERAL INSTRUCTIONS

THIS GAS FIREPLACE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to re- gion and it is important to know the specifics that apply to your area,

for example: in Massachusetts State:

•The fireplace damper must be removed or welded in the open position prior to installation of a fireplace insert or gas log.

•The appliance off valve must be a “T” handle gas cock.

•The flexible connector must not be longer than 36 inches.

•The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.

•WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth of Massachusetts.

In absence of local codes, install to the current National Fuel Gas Code, ANSI Z223.1, or the current CAN/CGA B149, Installation Codes.

Purge all gas lines with the glass door of the fireplace removed. Assure that a continuous gas flow is at the burner before installing the door.

Under extreme vent configurations, allow several minutes (5-15) for the flame to stabilize after igni- tion.

Altitudes greater than 4000ft. require a minimum vent run of 12ft.

The fireplace and its individual shutoff valve must be dis- connected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The fireplace must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

A 1/8 inch NPT plug, accessible for test gauge connection, must be installed immediately upstream of the gas supply connection to the stove.

This fireplace must be connected to any accepted lined chimney system listed to ULC-S635M (in Canada) or UL- 1777 (in USA). The venting connection must be in compli- ance with the vent manufacturers installation instructions. The draft hood must be installed so it is in the same atmo- spheric pressure zone as the combustion air inlet to the fireplace.

Provide adequate ventilation and combustion air. Pro- vide adequate accessibility clearance for servicing and operating the fireplace. Never obstruct the front open- ing of the fireplace.

This insert must be recessed into a vented noncombus- tible woodburning fireplace (prefabricated or masonry) only. The minimum fireplace size in which the heater is to be installed is:

HEIGHT 17½ inches WIDTH 25½ inches DEPTH 16½ inches The minimum distance, from the bottom of a combustible mantle projecting 6" maximum from the wall to the top of the unit, is 8".

The fireplace, when installed, must be electrically con- nected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the ANSI/ NFPA 70 NATIONAL ELECTRICAL CODE in the United States. The blower power cord must be connected into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

GENERAL INFORMATION

FOR YOUR SATISFACTION, THIS FIREPLACE HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION AND QUAL- ITY! Maximum input is 24,000 BTU/hr for natural gas and 22,000 BTU/hr for propane. When the fireplace is installed at elevations above 4,500ft, and in the absense of specific recommendations from the local authority having jurisdic- tion, the certified high altitude input rating shall be reduced at the rate of 4% for each additional 1,000ft. Maximum out- put for natural gas is 15,900 BTU/hr and 16,000 BTU/hr for propane.

Minimum inlet gas supply pressure is 4.5 inches water column for natural gas and 11 inches water column for propane. This fireplace is certified for bedroom and bedsitting room installation. Maximum inlet gas pressure is 7 inches water column for natural gas and 13 inches water column for propane. Manifold pressure under flow conditions is 3.5 inches water column for natural gas and 10 inches water column for propane.

No external electricity (110 volts or 24 volts) is required for the gas system operation.

Expansion / contraction noises during heating up and cool- ing down cycles are normal and to be expected. Change in flame appearance from "HI" to "LO" is more evident in natu- ral gas than in propane.

CARE OF GLASS AND PLATED

Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth. The glass is 3/16" ceramic glass available from your Continental / Wolf Steel Ltd. dealer. Do not substitute materials. Clean the glass after the first 10 hours of operation with a recommended gas fireplace glass cleaner. Thereafter clean as required.

Do not clean glass when hot! If the glass is not kept clean permanent discolouration and / or blemishes may result.

W415-0120 / E / 01.11.05

CBI 360-N, CBI 360-P specifications

The Continental CBI 360-N and CBI 360-P represent cutting-edge advancements in the realm of continental industrial solutions, designed specifically to meet the diverse needs of modern industries. These models stand out due to their innovative technologies, robust performance, and versatility, making them essential tools for various applications.

One of the defining features of the CBI 360-N and CBI 360-P is their exceptional durability. Built with high-quality materials, these models are engineered to withstand tough industrial environments, ensuring longevity and consistent performance even under extreme conditions. The robust construction not only enhances their lifespan but also reduces maintenance costs, offering a cost-effective solution for users.

Another significant aspect is the advanced monitoring and diagnostic technologies integrated into these models. They come equipped with smart sensors that provide real-time data on operating conditions, allowing for proactive maintenance and troubleshooting. This feature not only optimizes performance but also enhances safety by minimizing the risk of unexpected breakdowns.

The CBI 360-N and CBI 360-P also boast energy-efficient designs. With a focus on reducing energy consumption, these models are equipped with high-performance motors and intelligent control systems that optimize power usage. This not only contributes to lower operational costs but also aligns with global sustainability goals, making them an environmentally friendly choice.

Versatility is another hallmark of the CBI 360 series. The CBI 360-N is particularly suited for standard applications, while the CBI 360-P offers enhanced power capabilities for more demanding tasks. This flexibility allows operators to select the appropriate model based on their specific requirements, making these machines suitable for a wide range of industrial sectors, including manufacturing, logistics, and more.

Furthermore, user-friendly interfaces and intuitive controls are central to the design of the CBI 360-N and CBI 360-P. Operators can easily configure settings and monitor performance through streamlined control panels, enhancing productivity and reducing the learning curve for new users.

In conclusion, the Continental CBI 360-N and CBI 360-P stand at the forefront of industrial innovation, offering a blend of durability, efficiency, and versatility. Their advanced technologies and practical features make them invaluable assets for businesses looking to improve operational efficiency and reliability in an ever-evolving industrial landscape. With these models, Continental continues to lead the way in providing high-quality, dependable industrial solutions.