Desa VM36, M42 installation manual Opening Vent Damper, Removing Glass Doors

Page 17

INSTALLATION

Installing Optional Glass Door Accessory (Cont.) Opening Vent Damper

17

INSTALLATION

Continued

5.Once the top and bottom pins are secured, unfold the door into the closed position.

6.Repeat the process for the opposite door assembly.

7.To adjust the doors, slide them partially open. Using a screw- driver, loosen the hold-down screws in the spring clip (see Fig- ure 36) and pivot plate.

8.Close both doors until evenly joined at the middle and note the gap at the outer edges of the face.

9.Reopen one door at a time and retighten the upper and lower hold-down screws.

10.Repeat the process until both doors are evenly joined, spaced and working freely.

CAUTION: The glass panels become very hot while the appliance is operating. Do not attempt to adjust or clean the glass doors until the appliance has fully cooled.

The doors may be removed for replacement or cleaning as follows:

1.Partially open the door and press up on the upper spring clip with a screw driver until the outer top pivot pin is free of the clip.

2.Fully fold the frame assembly and slide the upper edge to- wards the center of the firebox opening until the guide pins are free of the frame rail (see Figure 37).

CAUTION: Always operate the appliance with the doors either fully opened or fully closed. Operating the appliance with the doors partially open can result in improper venting of flue products.

	Spring Clip
	Depress Spring
	Clip to Release
	Pivot Pin
Fold Bi-Fold
Door After
Releasing	Remove
Spring Clip and	Bottom Pin
Slide Door Out	From Pivot
of Upper Track	Plate While
	Sliding Door
	Out of the
	Upper Track
	Pivot Plate
Figure 37 - Removing Glass Doors

OPENING VENT DAMPER

Vent damper must be locked in the full open position before operating the fireplace. If vent damper is not open, fireplace will not light.

Spring Clip

	VENT DAMPER MUST BE LOCKED
	IN THE FULL OPEN POSITION
OPEN	TO OPERATE THE APPLIANCE	CLOSE
OPEN		CLOSE

Side Front Face

Hold-Down Screw

Partially	Figure 38 - Opening Vent Damper
Opened	Figure 38 - Opening Vent Damper
Door

Figure 36 - Adjusting Glass Doors

For more information, visit www.desatech.com

108795

Image 17

Contents Vent Decorative GAS Fireplace For Your SafetyNatural GAS What to do if YOU Smell GASSafety Information Table of ContentsUnpacking M36B,H/VM36B,H M42B,H/VM42B,H IntroductionBefore YOU Begin Model Product SpecificationsClearances PRE-INSTALLATION PreparationSelecting Location M36B,H M42B,H Mantel Clearances and Wall DetailsVM36B,H VM42B,H M36B,H M42B,H VM36B,H VM42B,HFraming Installing Transition Pipe and Starter CollarTypical B-Vent Configuration Venting InstallationMin Roof Pitch Checking for Proper VentingWall Switch Installation InstallationOptional Wireless HAND-HELD Remote Control Installation Installing ReceiverGAS Line HOOK-UP Installing 9-Volt Battery in Hand-Held Remote Control UnitOvertighten Ember and PAN Material PlacementInstalling Logs 1 LOG Placement for M36/VM36 ModelsInstalling Logs 1A, 1B LOG Placement for M42/VM42 ModelsAppliance Enclosure Installing Optional Glass Door AccessoryCombustion AIR KIT Model AK4 Optional Removing Glass Doors Opening Vent DamperOperating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To ApplianceInspecting Burners Pilot AssemblyOptional HAND-HELD Remote Operation Burner Flame PatternWiring Diagram Cleaning Maintenance Technical ServiceService Hints Replacement PartsObserved Problem Possible Cause Remedy TroubleshootingTroubleshooting Gas leak. See Warning statement at TopVM42B,H Models Illustrated Parts BreakdownM36B,H, M42B,H, VM36B,H and VM42B,H Models Parts ListLogset for M42B, H/VM42B, H Models Logs for M36B,H, M42B,H, VM36B,H and VM42B,H ModelsLogset for M36B, H/VM36B, H Models Accessories Warranty Information