Char-Broil 463440109 manual Troubleshooting Electronic Ignition, Section

Page 27

Troubleshooting - Electronic Ignition

Problem (Ignition)

Possible Cause

Check Procedure

Prevention/Solution

 

 

 

 

SECTION I

•Battery not installed

•Check battery orientation.

•Install battery (make sure that “+” and “–”

No sparks appear at

any electrodes when

properly.

 

connectors are oriented correctly, with “+” end up

control knob turned to

 

 

and “–” end down.)

; no noise can be

•Dead battery.

•Has battery been used

•Replace battery with new AA-size alkaline battery.

heard from spark

module.

 

previously?

 

 

•Button assembly not

•Check to insure threads are

•Unscrew button cap assembly and reinstall, making

 

installed properly.

properly engaged. Button

sure threads are aligned and engaged fully.

 

 

should travel up and down

 

 

 

without binding.

 

 

•Faulty spark module.

•If no sparks are generated

•Replace spark module assembly.

 

 

with new battery and good

 

 

 

wire connections, module is

 

 

 

faulty.

 

 

 

 

 

SECTION II

•Output lead

•Are output connections on

•Remove and reconnect all output connections at

No sparks appear at

connections not

and tight?

module and electrodes.

any electrodes when

connected.

 

 

control knob turned to

 

 

 

; noise can be

 

 

 

heard from spark

 

 

 

module.

 

 

 

SECTION III

•Output lead

•Are output connections on

•Remove and reconnect all output connections at

Sparks are present

connections not

and tight?

module and electrodes.

but not at all

connected.

 

 

electrodes and/or not

•Arcing to grill away

•If possible, observe grill in

•If sparks are observed other than from burner(s),

at full strength

 

from burner(s).

dark location. Operate

wire insulation may be damaged. Replace wires.

 

 

ignition system and look for

 

 

 

arcing between output wires

 

 

 

and grill frame.

 

 

•Weak battery.

•All sparks present but weak

•Replace battery with a new AA-size alkaline battery.

 

 

or at slow rate.

 

 

•Electrodes are wet.

•Has moisture accumulated

•Use paper towel to remove moisture.

 

 

on electrode and/or in burner

 

 

 

ports?

 

 

•Electrodes cracked or

•Inspect electrodes for

•Replace cracked or broken electrodes.

 

broken “sparks at

cracks.

 

 

crack”.

 

 

 

 

 

 

27

Image 27
Contents Date Purchased Estimated assembly time 45 minutesINSTALLER/ASSEMBLER California Proposition Installation Safety PrecautionsOnly LP cylinders equipped with this type of valve LP Liquefied Petroleum GasLP Cylinder Filling UL listed Overfill ProtectionLP Cylinder Exchange Connecting Regulator to the LP CylinderFor your safety UseDo not household cleaning agents. Damage to gasLeak Testing Valves, Hose and Regulator Connection, do not use this regulatorTurn all grill control knobs to OFF Open lid during lighting For Safe Use of Your Grill and to Avoid Serious InjuryIgnitor Lighting SDo not lean over grill while lightingBurner Flame Check General Grill CleaningSideburner Ignitor Lighting Sideburner Match LightingVery Important Burner tubes must reengage valve Cleaning the Burner AssemblyStoring Your Grill Turn gas off at control knobs and LP cylinderRegulator TemperatureFirst Time Use Lava Rock / BriquettesRotisserie Cooking Food SafetyDirect Cooking Indirect CookingUsda Recommended Safe Minimum Internal Temperatures Storing Your Grill Why Clean?General Cleaning Routine CareLimited Warranty Not Pictured Key Qty DescriptionParts Diagram Axle Hole LP tank hole Bottom ShelfAxle Washer Front PanelWheel Hitch PinGrill Head Qty 7X15 Fiber Washer Right Side ShelfSideburner Shelf Sideburner Heat Tent Swing Away Leg Wire Cooking GrateLP Tank Tank Thumbscrew Grease Cup ClipEmergencies Possible Cause Prevention/Solution TroubleshootingElectronic Ignition Section Troubleshooting Electronic IgnitionPage Page Page Regtemp REV00