DCS BGB30-BQR manual GAS Requirements, Total GAS Consumption of the Grill with ALL Burners on HI

FIG.01 Natural Gas

GAS REQUIREMENTS

Verify the type of gas supply to be used, either
natural or LP, and make sure the marking on the
appliance rating plate agrees with that of the
supply. The rating plate is located on the inside
back wall of the Grill. Never connect an			Bottom of unit
unregulated gas line to the appliance.		Coupling	Threading compound
		1/2 NPT	must be resistant to LP gas
An installer supplied gas shut-off valve must be
		Close
installed in an easily accessible location.	All	NIpple
		Regulator
installer supplied parts must conform to local		4.0" W.C.		1/2 NPT
				Close
codes, or in the absence of local codes, with the		Adapter 1/2 NPT
				NIpple
National Electrical Code, ANSI/NFPA 70 or the		to 3/8 flare fitting
		Do not put threading		Installer supplied shut-off
Canadian Electrical Code, CSA C22.1, and	the			valve must be easily
		compound on these
				accessible*
National Fuel Gas Code, ANSI Z223.1	or	threads
CAN/CGA-B149.1 Natural Gas Installation Code		*Installation must conform with local
		codes or with the National Fuel Gas
or CAN/CGA-B149.2 Propane Installation Code.		Code ANSI Z223.1 or the CAN/CGA-
		B149.2 Propane Installation Code

All pipe sealants must be an approved type and resistant to the actions of LP gases. Never use

pipe sealant on flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes and ordinances. In the absence of local codes, the installation must comply with the national fuel gas code ANSI Z223.1. Gas conversion kits are available from the factory. When ordering gas conversion kits have the model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BGB30-BQR - 50,0 00 Btu/hr

The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be isolated from the gas supply piping system by closing its individual manual shut- off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation of this appliance must conform with local codes or, in the absence of local codes, with the national fuel gas code, ANSI Z223.1. Installation in Canada must be in accordance with the Standard CAN/CGA-B149.2 Propane Installation Code and local codes.

NATURAL GAS HOOK UP: (This type of connection should be performed by a certified or licenced technician only.)

Connection: 1/2" NPT male with 3/8" flare adapter. Operating pressure: 4.0" W.C.

Supply pressure: 5" to 14" water column. If in excess of 14" W.C. a step down regulator is required. Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas line is too small, the grill will not function properly. Any joint sealant used must be an approved type and be resistive to the actions of LP gases.

TO HOOK-UP THE FITTINGS SUPPLIED WITH THE GRILL:

Assemble as shown (Fig.01). Use threading compound on male threads only. Do not use threading compound on the male end of the 1/2 NPT to 3/8 flare adapter. Use a second pipe wrench to hold the grill inlet pipe to avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of gas flow towards the unit, away from the supply. Do not forget to place the installer supplied gas valve in an accessible location.

7