Kenmore 141.16324, 141.16322 manual Install Ignitor Battery, Install Cooking Components

Page 16

Install Ignitor Battery

[] Unscrew the ignitor Cap from Control Panel.

[] Place supplied AA battery into the Ignitor Slot with positive pole facing you.

[] Position the Cap and Spring over the AA

battery and tighten onto Control Panel.

Main Burners Electrode Check

Perform this Electrode Check with the

assistance of another person.

This test will ensure that the Spark Electrode Tips are properly positioned so your grill lights easily and properly.

Spark Gap

Gas Collector Box

Inside Nut

AA BATTERY

IGNITOR

CAP_

j_

---.<.

SPRING

IGNITOR

SLOT

Spark Receiver Spark Electrode Tip

[]

Be

sure

all

Control

 

Knobs

are

set

to

 

"OFF"

 

and

open

the

Grill

Lid.

 

 

[]

Have

your

assistant

 

stand

behind

and to

 

the

right

of

the

grill

 

facing

toward

the

 

front

of

the

grill

bowl.

Never

put

your

 

face inside the Grill Bowl.

 

 

 

[]

Press

the

 

Ignitor

Cap. You

should

hear

 

a

"clicking"

 

sound.

Your

assistant

should

 

see

a

blue

spark

within

Left

Gas

 

 

Collector

 

Box.

if

a

spark is

present

the

 

Electrode

Tips

are

properly

positioned.

[]

if

no

spark

is

seen,

 

the

Spark

Gap

 

needs

 

to

be

adjusted

as

follows:

 

Using an adjustable wrench, loosen the inside Nut until the Gas Collector Box can

be turned upward.

if the gap between the Spark

Electrode Tip and Receiver is more than 3/16" use long nose pliers to

gently squeeze the Gas Collector Box to narrow the gap.

Return the Gas Collector Box to its original position, secure the inside Nut and try the Electrode Check again, if no "clicking" sound is heard:

-AA Battery may be installed back-

-wards. Electric wires may be loose. Remove the AA Battery and inspect the ignitor Junction Box found behind

the Control Panel and reconnect any loose wires.

Side Burner Electrode Check

[] Open the Side Burner Lid and remove the plastic shipping band from the burner and the pot support.

[] Be sure Control Knob is set to "OFF" and open the Side Burner Lid. Press the Ignitor

Cap. You should hear a "clicking" sound

and see a blue spark between the tip of the

electrode and burner.

[] If you don't see a spark from the side burner electrode, adjust gap between electrode and burner surface to 3/16 inches.

Install Cooking Components

[] Place the Savor Plates ® (holes face rear of bowl) on lower ledge above Burners.

[] Place Cooking Grids on bowl ledge.

[] Place the Secondary Cooking Rack into the slots on Grill Bowl Side Panels.

SECONDARY

COOKING RACK

Model 141.16322

SLOTS FOR SECONDARY

COOKING RACK

Model 141.16324

When you have finished assembling your grill be sure that all screws are tightened for safe operation of your grill.

Failure to read and follow the Use and Care

Instructions could result in a fire or explosion that could cause serious bodilyinjury, death or property damage.

16

Image 16
Contents Operatorsmanual Additional Limited Warranty on Specific Grill Parts One-Year Full Warranty on Kenmore GrillGrill Installation Codes Failure to comply with these instructions could Grill information CenterRedu Part Description QTY Purpose of Part Page 2436 Page KEY PIN QTY Description 16324 16322KEY Description PIN QTY 16322 16324Install Cart Legs Install Cart Bottom ShelfInstall Cart Rear Panel For Model 141.16324 only Install Casters and WheelsInstall Cart Side Panels Install Door Bracket, Magnetic Door Stops Door Stop PlateInstall Doors to Cart Install Door Handles and Door BoltsInstall Lighting Stick and Grease Draining Tray Install Left Side Shelf and Side Burner FrameInstall Side Burner Kit Install Cooking Components Install Ignitor BatterySide Burner Electrode Check Correct LP GAS Tank USE For you r safety How to Leak Test your LP Gas TankDisconnecting a Liquid Propane Gas LPG Tank From Your Grill Check all connections for LP Gas LeaksSide Burner Lighting Instructions Manually Lighting Your Grill By Paper MatchGrill Lighting Instructions Troubleshooting If the grill fails to light CorrectionAnnual Cleaning of The Grill Interior Cleaning The Grease Tray and ReceptacleCleaning Exterior Surfaces Extended Preheating Burn-OffUse your grill at least 3 feet away from any Page Question My grill will not light properly. Why? AnswerQuestion MY-HOME