Kenmore 141.16322, 141.16324 manual Extended

Page 23

To reduce

the chance

of FLASHBACK

FIRE

you

must

clean the

Burner

Tubes as follows

 

at least

once

a month

in summer and

fall

or whenever

spiders

are active in your

area, and

if your grill has not been

used

for

an

extended

period of

time.

 

 

 

 

 

 

 

1.Turn all Burner Valves to the full OFF position.

2.Turn the LP Gas tank valve to the full OFF position.

3.Detach the LP Gas regulator assembly from your gas grill.

4.Remove the Cooking Grids, Savor Plates ® and Grease Trays from your grill.

5.Remove the screw from the rear of each Burner using a Phillips Head Screwdriver.

6.Carefully lift each Burner up and away from the Gas Valve Orifice.

Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath the grill.

Refer to Figure 1 and perform one of these three cleaning methods:

[] METHOD 1: Bend a stiff wire or wire coat

hanger into a small hook as shown and run the hook through the Burner Tube and inside the Burner several times to remove debris.

.)

[] METHOD 2: Use a bottle brush with a

flexible handle and run the brush through the Burner Tube and inside the Burner

several times to remove any debris.

[] METHOD 3: Use an air hose to force air through each Burner Tube. The forced air

should pass debris or obstructions through the Burner and out the Ports.

Regardless of which Burner cleaning procedure you

use, we recommend you also complete the following steps to help prolong Burner life.

1.Use a fiber pad or nylon brush to clean the entire outer surface of each Burner until free of food residue and dirt.

2.Clean any clogged ports with a stiff wire, such as an open paper clip.

3.Inspect each Burner for damage (cracks or holes) and if such damage is found, order and install a new Burner. After installation, check to ensure that the Gas Valve Orifices are correctly placed inside the ends of the Burner Tubes. Also check the position of your Spark Electrode.

For safe operation ensure the Gas Valve Assembly Orifice is inside the Burner Tube before using your grill. See figure. If the Orifice is not inside the

Burner Tube, lighting the Burner may cause

explosion and/or fire resulting in serious bodily injury and/or property damage.

Gas Valve AssembIy

Orifice

BumerTube

Figure 1

TO CLEAN BURNER TUBE,

INSERT HOOK AS INDICATED BY THE ARROW

_

_

SSSDSSSSSDSSSSDDSSSDSDSSDSSDSDSSDDDSSSSDSSSSSSSSSSDSSSSDDSSSD_

\

BurnerTube

23

Image 23
Contents Operatorsmanual Grill Installation Codes One-Year Full Warranty on Kenmore GrillAdditional Limited Warranty on Specific Grill Parts Redu Grill information CenterFailure to comply with these instructions could Part Description QTY Purpose of Part Page 2436 Page 16324 16322 KEY PIN QTY Description16322 16324 KEY Description PIN QTYInstall Cart Bottom Shelf Install Cart LegsInstall Casters and Wheels Install Cart Rear Panel For Model 141.16324 onlyInstall Door Bracket, Magnetic Door Stops Door Stop Plate Install Cart Side PanelsInstall Door Handles and Door Bolts Install Doors to CartInstall Left Side Shelf and Side Burner Frame Install Lighting Stick and Grease Draining TrayInstall Side Burner Kit Side Burner Electrode Check Install Ignitor BatteryInstall Cooking Components Correct LP GAS Tank USE How to Leak Test your LP Gas Tank For you r safetyCheck all connections for LP Gas Leaks Disconnecting a Liquid Propane Gas LPG Tank From Your GrillGrill Lighting Instructions Manually Lighting Your Grill By Paper MatchSide Burner Lighting Instructions Correction Troubleshooting If the grill fails to lightCleaning Exterior Surfaces Cleaning The Grease Tray and ReceptacleAnnual Cleaning of The Grill Interior Extended Use your grill at least 3 feet away from any Burn-OffPreheating Page Answer Question My grill will not light properly. Why?Question MY-HOME