BeefEater Gas Barbecues manual Installation Instructions9 BeefEater Barbecues, LP Gas / Propane

Page 9

Important

This appliance must be installed in accordance with the installation requirements of the LOCAL GAS and ELECTRICITY supply authority, or the appropriate installation code issued by the A.G.A. and the A.L.P.G.A. Servicing should only be carried out by an authorised person.

Installation Instructions9 BeefEater Barbecues

Recommended minimum LPG cylinder capacity for use with this appliance is 4kg. Maximum LPG cylinder capacity for use with this appliance is 10kg.

Do not install the gas cylinder beneath the barbecue unless in conjunction with an approved separator panel.

This appliance:

•Must have a minimum clearance from combustible materials of all sides of the barbecue of 450 mm (18”).

•Should not be installed under or on any combustible surface.

•Must be tested for safe and proper operation on completion of installation and prior to leaving the site. Keep ventilation opening of any cylinder enclosure clear and free of any debris.

Check ‘Gas Type’ label & data plate attached to right side of barbecue.

LP Gas / Propane

A.Fit the regulator to the LPG cylinder. See Regulator Connection page 2, Fig 1.

B.Connect the hose and regulator to the gas inlet at the Rigthand side of the barbecue. The gas inlet of the barbecue is 3/8 SAE male flare fitting. Do not subject the hose to twisting.

C.Secure all joints spanner (wrench) tight but do not over-tighten. Check for leaks after turning on gas supply by brushing onto all joints a solution of water and detergent. Bubbling of the solution will indicate leaks. Re-tighten or reseal any leaking joints. If leaks persist turn off the gas supply and consult your dealer.

D.Following operating instructions light each burner and check for a clear blue flame with just a tip of yellow. Excess yellow tipping can be adjusted using the screw on the side of the burner. Turn the screw in a counter clockwise rotation to remove the yellow.

E.For mobile trolley installations, when using a flexible hose to a fixed fuel source, a chain or similar restraining device must be fitted to prevent strain on the gas supply hose or accidental uncoupling. Do not subject the hose to twisting.

F.For build-in situations allow adequate ventilation for the barbecue and cylinder. Keep the cylinder away from heat and allow clear access to the gas supply hose and regulator.

Natural Gas

(Natural Gas installation should be carried out by a qualified gas fitter).

A.BeefEater Natural Gas barbecues are designed for low- pressure (4.0” WC, 1.00KPa) to be used as freestanding units, trolley mounted, or built into brickwork.

B.Fit the natural gas regulator supplied directly to the gas inlet via hard plumbing and install a shutoff valve within easy reach in the gas line. Secure all joints spanner tight but do not over-tighten. Check for leaks after turning on gas supply by brushing onto all joints a solution of water and detergent. Bubbling of the solution will indicate leaks. Re-tighten or reseal any leaking joints. If leaks persist turn off the gas supply and consult the manufacturer or dealer.

C.Test gas pressure by removing the last burner from the left hand side of the barbecue and attaching a hose and pressure gauge to the end of the gas valve. Turn on two burners and check the pressure. Inlet pressure should be 4.0” WC or 1.00 KPa.

D.Following operating instructions light each burner and check for a clear blue flame with just a tip of yellow. Avoid excess yellow tipping by adjusting the screw on the side of the burner, counter-clockwise rotation removes yellow.

E.For mobile trolley installations a chain or similar restraining device must be fitted to prevent strain or accidental uncoupling of the gas supply line.

F.For build-in situations allow adequate ventilation for the barbecue.

The barbecue appliance must be isolated from the gas supply piping system by closing its manual shutoff valve during any pressure testing of the gas supply piping system.

Installation to Natural Gas must be carried out by an authorised person.

Right Wrong

WARNING: The flexible PVC hose assembly supplied must not be exposed to temperatures in excess of 60°C (140°F). DO NOT expose to the sun’s direct heat and DO NOT allow the hose to come in contact with the hot surface of the barbecue body.

Australia’s Leading Barbecue

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Signature S-3000E Signature PlusSignature S-3000S BalconyTable of Contents Beefeater Barbecues Spanner tighten all gas fittings as per instructions Precautions and Warnings3 BeefEater BarbecuesStandard POL Regulator Gas Cylinder Information Beefeater BarbecuesQuick Connect Regulator Obtainable from your nearest BeefEater stockistBeefEater Barbecues For Your SafetyHeat Reflectors, Burners And Vaporizers Assembly Instructions Beefeater BarbecuesHow Many Vaporizers And Reflectors Are There? Model Vaporizer ReflectorFitting The Heat Reflectors Fitting The BurnersFitting The Vaporizers Fitting The Grease Tray Fitting The Cooking Plates And GrillsRear of Barbecue Rear of Barbecue Grease drain holeInstallation Instructions9 BeefEater Barbecues LP Gas / PropaneNatural Gas Before Lighting 10Operating Instructions Beefeater BarbecuesAfter Use ‘Quartz Start’ IgnitionOperating Instructions BeefEater Barbecues Temperature Warnings 12Operating Instructions Beefeater BarbecuesCooking With The BeefEater Roasting Hood Clean off any food spills and then close the lid Operation Of The Optional Side BurnerLighting How Long Will The Gas In My Cylinder Last? 14Help Guide Beefeater BarbecuesCare And Maintenance Instructions Care and Maintenance BeefEater BarbecuesCleaning The Cooking Surfaces Cooking Surface Preparation16Care and Maintenance Beefeater Barbecues General Care And Maintenance InstructionsStainless Steel Cleaning And Maintenance Service And Maintenance Porcelain Enamel Cleaning MaintenanceDon’t Discoloration Of Stainless Steel18Outdoor Installation Instructions Beefeater Barbecues Typical Installation Drawing Propane LPG InstallationNatural Gas Installation Specifications BeefEater Barbecues 20Signature Series Spare Parts Beefeater Barbecues Ref # Description Signature Series Spare Parts BeefEater Barbecues22Warranty Terms and Conditions Beefeater Barbecues Warranty Administration Warranty Terms and Conditions BeefEater Barbecues24Accessories Beefeater Barbecues Tech SupportBeefEater Sales International

Gas Barbecues specifications

BeefEater gas barbecues have established themselves as a leader in outdoor cooking, combining innovative design with robust performance. Known for their durable construction and sleek aesthetic, these barbecues are perfect for outdoor enthusiasts who value both style and functionality.

One of the standout features of BeefEater gas barbecues is their high-quality materials. Built with stainless steel, they resist rust and corrosion, ensuring longevity and minimal maintenance. The precision-engineered burners provide exceptional heat distribution, allowing for even cooking across the grilling surface. Many models come equipped with up to four burners, offering flexibility for cooking various types of food at once.

Another key characteristic of BeefEater barbecues is their advanced technology. The signature Vapourizer Grid, a unique component of their grills, helps to reduce flare-ups while enhancing smoke flavor. This technology also ensures that the food retains its moisture, resulting in juicy and flavorful dishes. Integrated with heat-resistant thermometers, users can monitor internal temperatures without lifting the lid, ensuring perfectly cooked meats every time.

BeefEater designs also prioritize ease of use. The push-button ignition system allows for quick and convenient startup, and many units feature removable drip trays that simplify cleanup. Additionally, the double-walled hood helps retain heat and improve efficiency, making them ideal for both low and slow cooking or high-heat grilling.

Versatility is another critical aspect of BeefEater gas barbecues. With a range of features including rotisserie kits, side burners, and warming racks, these grills can accommodate a wide variety of cooking styles and methods. Whether it’s searing steaks, slow roasting a whole chicken, or simmering side dishes, BeefEater barbecues can do it all.

Finally, the modern design of BeefEater gas barbecues complements any outdoor space, enhancing the ambiance of gatherings and barbecues. With spacious cooking surfaces, ergonomic features, and customizable accessories, these grills not only deliver exceptional performance but also a user-friendly experience.

In summary, BeefEater gas barbecues stand out for their exceptional build quality, innovative technologies, ease of use, and aesthetic appeal. For anyone looking to elevate their outdoor cooking experience, investing in a BeefEater barbecue is a commitment to quality and excellence. Enjoy grilling like never before with one of the industry’s finest brands.
Top Page Image Contents