Broilmaster P4XFN-1, R3-1 manual Maintenance, Burn Off

Page 33

MAINTENANCE

Cleaning the Grill

Caution: To prevent injury, use care when cleaning a hot grill.

Note: Do not use a commercial cleaner on the cooking grid. Do not brush grids while they are hot. Do not scrape grids.

For baked on residue use a brass (NOT STEEL) brush on the cooking grid and other components.

Burn Off

This process is much like that used in self-cleaning ovens and is most efficient when completed after each use of the grill.

Caution: Do not open the grill during the burn off process. Opening the grill during the burn off process may cause a sudden grease fire flare up that could burn your face and arms. Wait until the grill has cooled before opening.

1.Turn gas knob to HI. Close lid and allow the grill to burn for ten minutes, or until no smoke is present. Do not allow the grill to burn for more than 30 minutes.

2.Turn gas knob and supply to OFF and allow the grill to cool.

3.Wipe COOL grill with a damp cloth to remove soot.

Grill Bottom

Periodically remove cooking grids and flare guard to clean the interior of the grill. Scrape off baked on residue with a putty knife or brass brush and rinse with water. Clean the bottom air holes with a small knife.

Burner Maintenance

Stainless steel burners often turn reddish brown after use. This does not effect the performance of the grill. When cleaning the interior of the grill, remove the burners and clean with a brass brush. Wash with water and a mild detergent.

Grease Cup

Empty periodically.

Venturi Tubes

The venturi tubes allow air and gas to mix prior to burning, thus ensuring an efficient flame. Spiders or other small insects may build webs or nests inside the tubes obstructing air flow. Fire, or flashback, can occur, in and/or around obstructed venturi tubes and can cause damage to components beneath the grill or an unsafe condition. To reduce risk, inspections and cleaning should be performed at least twice monthly when spiders are active. If the grill has been unused for an extended period of time inspect the tubes before using the grill.

Clean venturi tubes as follows:

1.Remove the cooking grids and briquette rack.

2.Remove the burner from the grill.

3.Lay the burner face down and remove the four retaining screws from the venturi tube plate and the burner. See Figure 23.

4.Use a small flexible brush to remove any debris for the tube(s).

5.Flush with water.

6.Allow the tube(s) to dry before reinstalling.

7.Reinstall the venturi tubes and burner.

Figure 23

Note: Bowtie burner is shown. Follow the same steps for the H burner assembly.

Exterior

Clean regularly with a solution of mild detergent and hot water. Touch-up paint is available from your dealer. Broilmaster® protec- tive covers are recommended. Stainless steel components can be easily cleaned with a spray-on stainless steel cleaner found in most hardware stores.

Briquettes

If the briquettes did not come clean during burn off, after cooling turn them over. The residue will burn off during warm-up for the next use.

B101623-5-1012

Page 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Models If YOU Smell GAS Empire Comfort Systems, Inc CongratulationsTable of Contents Parts Not Under Warranty HOW to Order Repair PartsWarranty Parts Master Parts Distributor ListP3X Series Parts Diagram P3SX P3SXN P3X P3XN P3XF P3XFN Index Part Description Part NumberP4X Series Parts Diagram P4XN P4XF P4XFN P4X Series Parts ListH3X Series Parts Diagram H3X Series Parts List Index No Part Description Part NumberH3X H3XN H4X Series Parts Diagram H4X H4XN H4X Series Parts ListR3 Series Parts Diagram R3 Series Parts List Index Description Part NumberR3N R3B R3BN Warranty Terms Grill AssemblyBefore You Begin Recommended ToolsWarranty Terms Propane GAS Grills Grill LocationCylinder Requirements Cylinder Storage Propane Cylinder SafetyConnection Requirements See FigurePressure Regulator and Hose Assembly Connecting to Propane Gas / Cylinder Retention MeansClockwise Gas Type Natural GAS GrillsH4XN-1 Phillips Truss Head Screw 10-24 X 3/4 Hardware PackHEX NUT, Lock Phillips Truss Head Screw 10-24 X Phillips Truss Head Screw 1/4-20 X 1 1/2Installing the Hose and Regula- tor Installing Control Panel ShieldInstalling Control Panel Installing the Ignitor Ignitor AssemblyInstalling Control Knobs See Figures 8Wind Deflector Installing the Burner Series Burner ShownSeries Shown Handle Installing Flare Busters Lid StopP3X P4X Installing Racks CleaningSee b Operation Propane & Natural GAS Grills Air Shutter AdjustmentChecking for Gas Leaks Operating InstructionsOperation Electrical AccessoriesBefore Cooking PreheatingBurn Off MaintenanceProblem Cause Solution TroubleshootingR3-1, R3N-1 ,R3B-1, R3BN-1 R3B only R3 onlyR3B only Description Part Number Quantit Supplied Safety Precautions Safety Practices to Avoid Personal InjuryOutdoor USE only Grill Assembly Grill Assembly Grill Assembly Lid stop assembly hardware GAS Conversion to Natural GAS GAS Conversion to Natural GAS General Overview Infrared CookingSteak 1 Thick Infrared Cooking Sample Times & Grid PositionsCooking Grid Position Using the Ignitor Air Shutter Adjustment For R3B Series OnlyAvoid Water DAM AGE to Burner Clean burner venturi tubes as follows Blue Flame Burner MaintenanceGeneral Overview Infrared Burner MaintenanceBurn Off Standard CleaningProblem Cause Solution Appliance Service History Appliance Service History Appliance Service History Broilmaster
Related manuals
Manual 32 pages 17.57 Kb

P4XFN-1, R3-1 specifications

Broilmaster has been a trusted name in outdoor cooking, and their R3 series of gas grills, which includes models R3N-1, R3-1, R3BN-1, and R3B-1, exemplifies quality, performance, and innovation. Each model is thoughtfully designed to meet the demands of the modern grill master while ensuring a user-friendly experience.

One of the standout features of the Broilmaster R3 series is its powerful cooking system. All models are equipped with a high-performance stainless steel burner, providing even heat distribution and efficient cooking. This ensures that your food is cooked to perfection, whether it's a juicy steak, flavorful chicken, or grilled vegetables. The burners are designed to reach high temperatures quickly, allowing for searing and rapid cooking, which is essential for achieving that perfect char.

The R3N-1, R3-1, R3BN-1, and R3B-1 models feature an innovative cooking grid construction made from cast iron, which retains heat exceptionally well and provides excellent grill marks on your food. The cast iron grids, combined with the burners, create an optimal cooking environment that can accommodate various cooking styles, from direct grilling to indirect cooking.

Another significant characteristic of these grills is their durability. Constructed from heavy-duty materials, including rust-resistant stainless steel, the R3 series is built to withstand the elements, ensuring longevity and consistent performance. The grills come with a stylish and functional hood that not only enhances their aesthetic appeal but also helps retain heat effectively during the cooking process.

For added convenience, the R3 models feature an integrated ignition system that ensures reliable startup every time you fire up the grill. Many of the models also come with built-in side shelves, providing additional workspace for food preparation and storage of grilling tools. The added versatility of these grills allows users to explore a variety of cooking methods, including smoking and baking when equipped with optional accessories.

In summary, the Broilmaster R3N-1, R3-1, R3BN-1, and R3B-1 gas grills are excellent options for anyone looking to elevate their outdoor cooking experience. With their powerful burners, durable construction, and user-friendly features, they cater to both novice grillers and seasoned barbecue enthusiasts alike. The R3 series not only embodies excellent performance but also offers the versatility and reliability necessary for any grilling occasion.
Top Page Image Contents