Weber A103.A, B069.A, C075.A manual Warranty, Customer Service Center South Hicks Road Palatine, IL

Page 3

Warranty

Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Grill that it will be free of defects in material and workmanship from the date of purchase as follows:

Aluminum Castings, lifetime, 1 year paint Porcelain Hood Section, 25 years Burners, 10 years

Igniter, 3 years

Cooking Grates, 7 years no rust through Flavorizer Bars, 5 years no rust through Thermoplastic/Thermoset Parts,

10 years Excluding fading All Remaining Parts, 5 years,

when assembled and operated in accordance with the printed instructions accompanying it.

Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use and service and which on examination shall indicate, to Weber’s satisfaction, they are defective. Before returning any parts, contact the Customer service representative in your region using the contact information sheet provided with your manual. If Weber confirms the defect and approves the claim, Weber will elect to replace such parts without charge. If you are required to return defective parts, transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this owner’s manual.

Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to you.

Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.

Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Weber.

This Warranty applies only to products sold at retail.

WEBER-STEPHEN PRODUCTS CO.

Customer Service Center

250 South Hicks Road

Palatine, IL 60067-6241

USA

A-3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Gas Grill Liquid Propane GAS Units only Customer Service Center South Hicks Road Palatine, IL WarrantyContents General Instructions Genesis Silver-C NG Page Page Page Page Assemble frame Assemble wheel frameAdd back panel Continue frame assemblyComplete frame assembly Add front panelInsert casters Add cooking box assemblyOmmend That this Installation be Done by a Professional Install Gas Supply General Specifications for PipingInstall igniter Gas Line PipingTest Connections Install manifold bracket Check that all burner valves are offConnect flexible hose to manifold Install the slide out bottom tray Install Lid Right swing-up work surface Install the right end trim piece with tool holdersBoard Do not use the swing-up work surface as a cuttingYou will need side burner Install side burnerWay and do not add bolts yet Install the left end trim piece and swing-up workSurface Shown, do not push the trim piece in allDo not use the work surface as a cutting board Install the work surfaceChecking Check for gas leaksTime you disconnect and reconnect a gas fitting Your barbecue was dealer or store assembledBox with the rounded sides up Install Flavorizer Bars and Cooking GratesRetighten the fitting with a wrench and recheck for Set the cooking grates onto the ledges in the cookingInstall the thermometer Installing the warming rack Install the bottom shelfTo Extinguish LightingManual Lighting Lighting only the side burner Lighting the Side BurnerCleaning CookingStorage Inspection and Cleaning of the Weber Spider Stopper Guards Annual MaintenanceWeber Spider Stopper Guards General MaintenanceReplacing Main Burners Crossover Ignition System Operations Smell of gas Flame is low when burner is onBurners burn with a yellow or Orange flame, in conjunction withConjunction with the smell of gas Side Burner does not lightFlame is low in High position Flame is very yellow

C075.A, A103.A, B069.A, D082.A specifications

The Weber D082.A, B069.A, A103.A, and C075.A are part of Weber's distinguished range of high-performance electronic control devices, specifically designed for various industrial and commercial applications. Each model showcases distinctive features and cutting-edge technologies that enhance operational efficiency and reliability.

The Weber D082.A is renowned for its robust build, integrating advanced automation technology. It offers versatile programming options that allow users to customize operation modes based on specific applications. The D082.A supports multiple communication protocols, ensuring seamless integration with existing control systems. It is equipped with a high-resolution display for real-time monitoring and diagnostics, enabling users to make quick adjustments and enhance productivity. The protective design resists environmental challenges, making it suitable for harsh industrial settings.

Next, the B069.A model is designed with an emphasis on energy efficiency. It employs intelligent power management systems to reduce energy consumption while maintaining high output performance. This device is also equipped with advanced fault detection algorithms that quickly identify potential issues, minimizing downtime. Moreover, the B069.A features an intuitive user interface that simplifies configuration and operation, ensuring that even operators with limited technical knowledge can manage the system effectively.

The A103.A highlights its adaptability through modular design, allowing businesses to tailor the unit to their specific requirements by adding or removing components as needed. This flexibility is complemented by enhanced safety features, including emergency stop mechanisms and fail-safe operations, which ensure user protection in the event of system malfunctions. Additionally, the A103.A is designed for ease of maintenance, with quick-access panels that facilitate routine checks and service.

Finally, the C075.A model is characterized by its advanced analytics capabilities. With real-time data collection and analysis, this device enables users to optimize processes and predict maintenance needs. The C075.A incorporates state-of-the-art sensor technology, providing accurate monitoring of various parameters, including temperature, pressure, and flow rates. This information can be invaluable for industries that demand precision and compliance with regulatory standards.

In summary, the Weber D082.A, B069.A, A103.A, and C075.A collectively offer a range of advanced features and technologies aimed at improving industrial operations. Their unique characteristics cater to the diverse needs of modern enterprises, emphasizing efficiency, adaptability, and safety across various applications.
Top Page Image Contents