Weber C075.A, B069.A, D082.A, A103.A manual General Instructions

Page 5

General Instructions

Your Weber Gas Barbecue is a portable outdoor cooking appliance. With the Weber Gas Barbecue you can grill, barbecue, roast and bake with results that are difficult to duplicate with indoor kitchen appliances. The closed lid and Flavorizer® Bars produce that “outdoor” flavor in the food.

The Weber Gas Barbecue is portable so you can easily change its location in your yard or on your patio. Portability means you can take your Weber Gas Barbecue with you if you move.

The natural gas supply is easy to use and gives you more cooking control than charcoal fuel.

•These instructions will give you the minimum requirements for assembling your Weber Gas Barbecue. Please read the instructions carefully before using your Weber Gas Barbecue. Improper assembly can be dangerous.

•Not for use by children.

•If there are local codes that apply to portable gas grills, you will have to conform to them. If there are no local codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1.

•This Weber Gas Barbecue is designed for natural (piped in city) gas only. Do not use liquid propane (LP) bottled gas. The valves, orifices and hose are for natural gas only.

•Do not use with charcoal fuel.

•Check that the area under the control panel and the bottom tray are free from debris that might obstruct the flow of combustion or ventilation air.

For Installation in Canada

These instructions, while generally acceptable, do not necessarily comply with the Canadian Installation codes, particularly with piping above and below ground. In Canada the installation of this appliance must comply with local codes and/or Standards CAN/ CGA-B149.1 (Installation Code for Natural Gas Burning Appliances and Equipment).

Storage

•The gas must be turned OFF at the natural gas supply when the Weber Gas Barbecue is not in use.

•When the Weber Gas Barbecue is stored indoors, the gas supply must be disconnected.

Operating

WARNING: Only use this barbecue outdoors in a well-ventilated area. Do not use in a garage, building, breezeway or any other enclosed area.

WARNING: Never use your Weber Gas Barbecue under an unprotected combustible roof or overhang.

WARNING: Your Weber Gas Barbecue is not intended to be installed in or on recreational vehicles and/or boats.

WARNING: Do not use combustible materials within 24 inches of the top, bottom, back or sides of the grill.

WARNING: The entire cooking box gets hot when in use. Do not leave unattended.

WARNING: Keep any electrical supply cord and the fuel supply hose away from any heated surface.

WARNING: Keep the cooking area clear of flammable vapors and liquids, such as gasoline, alcohol, etc., and combustible materials.

Gas Supply Testing

•Disconnect your Weber Gas Barbecue when the gas supply is being tested at high pressures. This appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

•Turn OFF your Weber Gas Barbecue when the gas supply is being tested at low pressures. This appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at the pressure equal to or less than 1/2 psig (3.5 kPa).

A-5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Gas Grill Liquid Propane GAS Units only Customer Service Center South Hicks Road Palatine, IL WarrantyContents General Instructions Genesis Silver-C NG Page Page Page Page Assemble frame Assemble wheel frameComplete frame assembly Continue frame assemblyAdd front panel Add back panelInsert casters Add cooking box assemblyOmmend That this Installation be Done by a Professional Install Gas Supply General Specifications for PipingTest Connections Install igniterGas Line Piping Connect flexible hose to manifold Install manifold bracketCheck that all burner valves are off Install the slide out bottom tray Install Lid Right swing-up work surface Install the right end trim piece with tool holdersBoard Do not use the swing-up work surface as a cuttingYou will need side burner Install side burnerSurface Install the left end trim piece and swing-up workShown, do not push the trim piece in all Way and do not add bolts yetDo not use the work surface as a cutting board Install the work surfaceTime you disconnect and reconnect a gas fitting Check for gas leaksYour barbecue was dealer or store assembled CheckingRetighten the fitting with a wrench and recheck for Install Flavorizer Bars and Cooking GratesSet the cooking grates onto the ledges in the cooking Box with the rounded sides upInstall the thermometer Installing the warming rack Install the bottom shelfTo Extinguish LightingManual Lighting Lighting only the side burner Lighting the Side BurnerStorage CleaningCooking Inspection and Cleaning of the Weber Spider Stopper Guards Annual MaintenanceWeber Spider Stopper Guards General MaintenanceReplacing Main Burners Crossover Ignition System Operations Burners burn with a yellow or Flame is low when burner is onOrange flame, in conjunction with Smell of gasFlame is low in High position Side Burner does not lightFlame is very yellow Conjunction with the smell of gas

C075.A, A103.A, B069.A, D082.A specifications

The Weber D082.A, B069.A, A103.A, and C075.A are part of Weber's distinguished range of high-performance electronic control devices, specifically designed for various industrial and commercial applications. Each model showcases distinctive features and cutting-edge technologies that enhance operational efficiency and reliability.

The Weber D082.A is renowned for its robust build, integrating advanced automation technology. It offers versatile programming options that allow users to customize operation modes based on specific applications. The D082.A supports multiple communication protocols, ensuring seamless integration with existing control systems. It is equipped with a high-resolution display for real-time monitoring and diagnostics, enabling users to make quick adjustments and enhance productivity. The protective design resists environmental challenges, making it suitable for harsh industrial settings.

Next, the B069.A model is designed with an emphasis on energy efficiency. It employs intelligent power management systems to reduce energy consumption while maintaining high output performance. This device is also equipped with advanced fault detection algorithms that quickly identify potential issues, minimizing downtime. Moreover, the B069.A features an intuitive user interface that simplifies configuration and operation, ensuring that even operators with limited technical knowledge can manage the system effectively.

The A103.A highlights its adaptability through modular design, allowing businesses to tailor the unit to their specific requirements by adding or removing components as needed. This flexibility is complemented by enhanced safety features, including emergency stop mechanisms and fail-safe operations, which ensure user protection in the event of system malfunctions. Additionally, the A103.A is designed for ease of maintenance, with quick-access panels that facilitate routine checks and service.

Finally, the C075.A model is characterized by its advanced analytics capabilities. With real-time data collection and analysis, this device enables users to optimize processes and predict maintenance needs. The C075.A incorporates state-of-the-art sensor technology, providing accurate monitoring of various parameters, including temperature, pressure, and flow rates. This information can be invaluable for industries that demand precision and compliance with regulatory standards.

In summary, the Weber D082.A, B069.A, A103.A, and C075.A collectively offer a range of advanced features and technologies aimed at improving industrial operations. Their unique characteristics cater to the diverse needs of modern enterprises, emphasizing efficiency, adaptability, and safety across various applications.
Top Page Image Contents