Installing work Surfaces & Gas Connection Guidelines
Install Left Work Surface |
|
|
|
|
|
| Check that all burner valves are off | ||||||||
|
|
|
|
|
| ||||||||||
You will need left work surface, two 1/2 inch bolts, two |
| You will need: burner control knobs. | |||||||||||||
| |||||||||||||||
nylon washers and a 7/16 inch or adjustable wrench. |
| Valves are shipped in the OFF position, but you should | |||||||||||||
| |||||||||||||||
| |||||||||||||||
Insert the left work surface tabs in the slots in the |
| check to be sure that they are turned OFF. Put the | |||||||||||||
| |||||||||||||||
| |||||||||||||||
frame(1). Slip washers on the bolts and insert the bolts |
| knob on each valve. Check by pushing down and | |||||||||||||
| |||||||||||||||
as shown(2). Tighten |
|
|
|
|
|
| turning clockwise. If they do not turn, they are off. | ||||||||
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Proceed to the next step. If they do turn continue |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(1) |
|
|
|
|
|
|
|
| (2) |
|
|
|
|
| turning them clockwise until they stop, then they are |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| off. Proceed to the next step. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fill liquid propane cylinder
Note - The liquid propane cylinder manufacturer is responsible for the materials, workmanship and performance of the cylinder. If the cylinder has a defect, malfunctions, or you have a question regarding the cylinder, call the cylinder manufacturer’s customer service center. The phone number is on the warning decal, which is permanently attached to the cylinder. If the cylinder manufacturer has not resolved the issue to your satisfaction, then contact the Customer Service Representative in your region using the contact information sheet provided with your manual.
To fill, take the liquid propane cylinder and filler adapter to an RV center or look up
WARNING: We recommend that your liquid propane cylinder be filled at an authorized liquid propane gas dealer by a qualified attendant, who fills the tank by weight.
IMPROPER FILLING IS DANGEROUS.
Tell your liquid propane dealer that this is a new liquid propane cylinder. The air must be removed from a new liquid propane cylinder before the initial filling. Your liquid propane cylinder dealer is equipped to do this. The liquid propane cylinder must be installed, trans- ported and stored in an upright position, and should not be dropped or handled roughly.
Never store or transport the liquid propane cylinder where temperatures can reach 125° Fahrenheit (too hot to hold by hand – for example: do not leave the liquid propane cylinder in a car on a hot day).
For full instructions on safe handling of liquid propane cylinders, see Section “Operating”.
C016.b |