Weber 3000 owner manual Parts List

Page 39

Parts List

All items are single quantities unless otherwise specified.

Parts can be ordered directly from Weber-Stephen Products Company by phone or mail.

Note - Do not return parts to Weber-Stephen Products Co. without first contacting the Customer Service Center by mail or phone. Returning the part may not be necessary.

1Lid (assembly)

2Lid handle

3Warm-Up Basket

4Warming rack

5Short Flavorizer Bars (8)

6Long Flavorizer Bars (5)

7Cooking grates (2)

8Work table

9Tubing plugs (5)

101/4-20 x 2 inch bolts (5)

11Swing table end bracket

12Left frame

13Swing table

141/4-20 x 1/2 inch bolts (6)

151/4 inch nylon washers (18)

16Slide bar assembly

1710-24 x 1 3/4 inch machine screws (2)

1810-24 hex nuts (2)

19Caster frame

20Casters (2)

21Bottom tray mounting rails (2)

22Bottom tray

23Catch pan holder

24Catch pan

25Drip pans (2)

26Frame connectors (2)

27Accessory trays (2)

28Wheel hub caps (2)

29Wheels (2)

30Axle

31Front panel

32Wheel frame

331/4-20 hex nut

34Side burner locks (2)

35Tank glides (2)

36Glide axle

37Glide hubcaps (2)

38Tank panel

391/4-20 x 1 1/4 inch bolt

While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Service Center toll free 1-800-446-1071to receive immediate assistance. Have your owner’s manual and serial number of the barbecue available for reference.

Weber-Stephen Products Company Customer Service Center

250 South Hicks Road

Palatine, IL 60067-6241 (800) 446-1071

40Hair pin cotters (2)

41Hinge pins (2)

42Thermometer

431/4-20 keps nut

44Cooking box

45Burner control knobs (3)

46Control panel

47Igniter button

48Phillips screws/washers (2)

49Crossover tube

50Front or Back burner

51Center burner

521/4-20 stainless steel wing nuts (2)

53Spider Stopper Guards (4)

54Manifold assembly

55Manifold bracket

56Side burner assembly

57Burner grate

58Side burner knob

59Tool holders (3)

60Right frame

61Igniter

62Igniter lock nut

63Igniter wire (black)

64Igniter wire (white)

65Gas catcher ignition chamber

66Fuel scale

671/4-20 wing nuts (2)

68LP tank

69Filler adapter

70Control panel inserts (2)

mWARNING: Use only Weber factory authorized parts. The use of any part that is not factory authorized can be dangerous. This will also void your warranty.

39

Image 39
Contents Genesis 3000 Series LP GAS Units only MDANGER MWARNINGSWarranty Patents and Trademarks Contents Operating area For Installation in CanadaGeneral Instructions StorageAssembly Check package contentsStep BER E W REB Check contents of hardware packs Assemble frame Assemble wheelsContinue frame assembly Complete frame assemblyInsert casters Add cooking box Install side burner locksAdd fuel scale Install tank panel assemblyCheck that all burner valves are off Install igniterInstall side burner Install manifold bracketMWARNING Make sure gas supply is OFF MCAUTION Do not remove adjustment wing nut from tank scale Set LP fuel scaleFill LP tank Connect LP tank MWARNING Do not ignite burners while leak checking Check for gas leaksInstall the bottom tray Install Flavorizer Bars and Cooking GratesInstall tool holders, control panel and burner control knobs Install the lidInstall swing table Secure side burnerMCAUTION Make sure both locks have snapped into place Notch to the front Slide bar View from front of barbecue Complete accessory installation To Extinguish LightingManual Lighting Lighting only the side burner. Figure Lighting the side burnerStorage and/or Nonuse Periodic CleaningCooking Storage and/or NonuseConnecting the filled LP tank Refilling the LP tankRemoval of the LP tank Male fitting Regulator Collar Quick disconnect engaged Safe handling tips for LP Gas Liquid Propane LP TanksDate Tested Inspection and Cleaning of the Weber Spider Stopper Guards Annual MaintenanceMain Burner Flame Pattern General MaintenanceMCAUTION Do not enlarge the burner ports when cleaning Weber Spider Stopper GuardsTo reinstall burners, reverse steps c through g Crossover Ignition System Operations Burner flame pattern is erratic. Flame is low When burner is on HIGH. Flames do not runBurner does not light, or flame is low in High position MCAUTION Do not line the bottom tray with aluminum foilSide Burner Maintenance Side Burner TroubleshootingPage 14-15 17-18 21-22 26 27 Parts List Final Word Thanks