Brinkmann Gourmet Series owner manual Filling the LP GAS Cylinder, Hose and Regulator

Page 7

WARNING

FILLING THE LP GAS CYLINDER:

•Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder.

•New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank.

•DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or flame an explosion causing severe burns, bodily harm, or death could occur.

•Always use a protective cylinder cap when grill is not connected to cylinder.

•If you exchange a cylinder with a qualified exchange program, be sure the cylinder has a Type 1 valve and an over-filling prevention device (OPD).

INSTALLING THE LP GAS CYLINDER ONTO THE GRILL:

1. Check that the cylinder valve is closed by turning the knob clockwise.

2. Place the cylinder into the tank holder in the bottom of cabinet.

3. Orient the cylinder such that the valve opening faces the side burner, and so that the hose is not kinked or damaged.

4. Fully tighten the cylinder clamp underneath tank holder to secure tank.

Tank Holder

5.Attach or detach regulator to the LP gas cylinder only when cylinder is at rest in tank holder.

HOSE AND REGULATOR:

Your grill is equipped with a Type 1 connection device with the following features:

1.The system will not allow gas flow from the cylinder until a positive connection to the valve has been made.

Note: The cylinder valve must be turned off before any

 

connection is made or removed.

Cylinder Clamp

2.A thermal device that will shut off the gas flow if the device is subject to temperatures above 240°F to 300°F (115°C to 150°C). If this should happen, remove the entire regulator assembly and dispose of properly. A replacement regulator assembly can be purchased by contacting customer service

at 800-527-0717. The cause of the excessive heat should be determined and corrected before using your grill again.

3. A regulator flow limiting device, when activated, restricts the flow of gas to 10 cubic feet per hour. If the flow limiting device is activated, perform Regulator Resetting Procedure.

REGULATOR RESETTING PROCEDURE

1.Turn burner control knobs to "OFF”, turn off the cylinder valve and disconnect regulator from LP gas tank. Wait approximately two minutes.

2.Reattach regulator and slowly turn cylinder valve back on. The flow limiting device will now be reset.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Stainless Steel Gas Grill Gril à Gaz en Acier Inoxydable Important Safety Table of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Hose and Regulator Installing the LP GAS Cylinder Onto the GrillRegulator Resetting Procedure Filling the LP GAS CylinderConnecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderWhen to Perform a Leak Test Leak TestingChecking for Leaks PRE-START Check List Lighting the Main Burners Lighting InstructionsMatch Lighting the Main Burners Match Lighting the Side Burner Lighting the Side BurnerTurning OFF the Grill Controlling FLARE-UPS Operating the GrillBreaking in Your Grill Preheating the GrillSide Burner Rotisserie CookingGrilling to Proper Temperature CleanlinessHelpful Hints Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceBefore Storing Your Grill Cooking GrillsHeat Distribution Plates Transporting and StorageTrouble Shooting Frequently Asked Questions Frequently Asked Questions Parts BAG Contents Parts List Assembly InstructionsFor Missing PARTS, Please Call Customer Service AT Step Locking Caster Hex Nut Wrench Step Place grease cup in middle of hole in heat shield plate Step Side Table Front Panel Side Burner Hose Place the side burner grate onto the side burner table Step Charmglow 7310 Assembled Importantes Relatives LA Sécurité Mises EN GardeTable DES Matières Mises EN Garde Mises EN Garde GénéralesBouteille DE GPL NON Fournie Avec CE Gril Renseignements SUR L’INSTALLATIONSpécifications DE LA Bouteille Procédure DE Réenclenchement DU Régulateur Installation DE LA Bouteille DE GPL SUR LE GrilRemplissage DE LA Bouteille DE GPL Tuyau ET RégulateurRaccordement DU Tuyau ET DU Régulateur Quand Effectuer UNE Épreuve D’ÉTANCHÉITÉ Épreuves D’ÉTANCHÉITÉListe DE Contrôle Avant L’ALLUMAGE Allumage DES Brûleurs Principaux Consignes D’ALLUMAGEAllumage DES Brûleurs Principaux À L’AIDE D’UNE Allumette Allumage DU Brûleur Latéral À L’AIDE D’UNE Allumette Allumage DU Brûleur LatéralFermeture DU Gril Contrôle DES Embrasements Utilisation DU GrilMise EN Marche DE Votre Gril Préchauffage DU GrilBrûleur Latéral Cuisson AU TournebrocheGrillage À LA Bonne Température PropretéConseils Utiles Assemblage ET Entretien DES Brûleurs Nettoyage ET EntretienAvant Dentreposer Votre Gril Grilles DE CuissonPlaques DE Diffusion Thermique Transport ET EntreposageDépannage Questions Posées Fréquemment Questions Posées Fréquemment Contenu DU SAC DE Pièces Liste DES Pièces Consignes D’ASSEMBLAGEEN CAS D’ABSENCE DE PIÈCES, Appeler LE Service Clientèle AU Étape Roulette à Blocage Clé pour Écrou Hexagonal Étape Contenant à Graisse Plaque Pare-Chaleur Corps du Gril Étape Du Tuyau Bouton de Étape Charmglow 7310 Assemblé Page Page Warranty
Top Page Image Contents