Tanita WB-300 instruction manual Product Specifications, Important Notes for Users

Page 2

1. Product Specifications

Product Model

WB-300 (Basic Electronic Medical Beam Scale)

 

WB-300MH (Electronic Medical Beam Scale

 

with Mechanical Height Rod)

 

WB-300DH (Electronic Medical Beam Scale

 

with Digital Height Rod and BMI Function)

Type of Measurement

Four (4) Half Bridge Load Cell

Capacity

440 lb – 0.1 lb

 

 

200 kg – 0.05 kg

Graduation

0.1 lb, 1/4 lb, 0.05 kg

Range of Height (WB-300MH and DH)

22" to 82" (55 cm – 208 cm)

Height Graduation (WB-300MH and DH)

1/4" (1.0 cm)

 

Power Source

(3) AA Alkaline batteries (included) for

 

scale functions

 

 

(1) 3-volt CR123 Lithium battery (included) for

 

clock display

 

Display

Dual panel LCD 1.0" display

 

(liquid crystal display)

Platform Size

Extra Large 16" x 12" x 2-3/4" non-slip platform

Product Dimensions

16.26" (413 mm) x 20.75" (527 mm) x 51.02"

 

(1296 mm)

 

Product Weight

WB-300

26.00 lb/11.80 kg

 

WB-300MH

27.50 lb/12.50 kg

 

WB-300DH

27.50 lb/12.50 kg

2. Important Notes for Users

Handling Tips

This scale is a precision instrument utilizing state-of-the art technology. To keep the unit in the best condition, follow these instructions carefully.

Do not attempt to disassemble the measuring platform and display.

Avoid excessive impact or vibration to the unit.

Place the unit in an area free from direct sunlight, heating equipment, high humidity, or extreme temperature change.

Never submerge in water or spill chemical liquids. To clean, use a dampened cloth and mild detergent.

If the product will not be used for a long period, remove the batteries before storage.

Moving the Scale

The scale has two rear wheels on the back of the platform. To avoid damage, use the wheels when moving the scale. Hold the display head securely and tilt the scale back about 30-45 degrees. Wheels will allow easy movement. IMPORTANT: Any time the scale is moved or re-located, be sure to press the ‘Zero’ key before use.

Disabling Key Sounds

To confirm a key operation has been selected, a “beep” will sound when any key is pressed. To disable this sound, press the up arrow and down arrow keys simultaneously for three seconds. To re-activate the key sound, press the up arrow and down arrow keys simultaneously again for three seconds. The volume of this beep sound is not adjustable.

Changing Measurement Units

This function can be used to change the measurement units on the Weight display: lb, kg, and fractional lb. The measurement unit keys are located on the left display panel. You may press this key before or while the user is on the platform.

Press ‘LB’ to set to pound mode. Decimal weight value in pound mode (0.1 lb increments) Press ‘KG’ to set to kilogram mode. Decimal weight value in kilogram mode (0.05 kg increments)

Press ‘LB (F)’ to set to fractional pound mode. Fractional weight value in pound mode (1/4 lb increments)

2

Image 2
Contents Table of Contents Electronic Physician ScaleProduct Specifications Important Notes for UsersComponents Description 1900Key Operation Weight LCD Right Side Clock LCD Assembly Instructions List of ComponentsInsert the Batteries Before UseLevel the Scale Remove the LCD CoverSet up the Clock Setting to ZeroAuto-on Function Weighing ProcedureInstructions for Use Turn-on FunctionWake-up Function Measuring Height Procedure WB-300MH and DH Reading the height Measurement Or More General Troubleshooting Weight Capacity ‘E’Replacing Batteries Resetting the ScaleCalibration Tanita Corporation