Pride Mobility 614 2SP, 614 2HD manual To replace the batteries, Corrective Maintenance

Page 37

V I I . C A R E A N D M A I N T E N A N C E

To replace the batteries:

1.Turn off the power to the controller.

2.Make sure that the power chair is in drive mode. See III. “Your Power Chair.”

3.Pull to remove the rear shroud. See figure 22.

4.Push down on the disconnect release button and disconnect the rear battery harness from the power base. See figure 22.

5.Unfasten the battery strap from around the rear battery.

6.Slide the rear battery out.

7.Push down on the disconnect release button and disconnect the front battery barness from the power base. See figure 22.

8.Remove the front battery.

9.Remove the battery harness from each battery.

10.Install a battery harness onto each new battery according to the battery wiring diagram. See figure 22. Make sure that you connect the red wire to the positive (+) battery terminal and the black wire to the negative (-) battery terminal for each battery.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

11.Place the batteries back into the power base.

12.Fasten the battery strap around the rear battery.

13.Connect each battery harness to its mating plug on the power base.

14.Reinstall the rear shroud.

15.Charge the batteries. See VI. “Batteries and Charging.”

When to See Your Authorized Pride Provider for Service

The following symptoms could indicate a serious problem with your power chair. If necessary, contact your authorized Pride Provider. When calling, have the model number, serial number, nature of the problem, and the error code if available.

!Motor noise

!Frayed harnesses

!Cracked or broken connectors

!Uneven wear on any of the tires

!Jerky motion

!Pulling to one side

!Bent or broken wheel assemblies

!Does not power up

!Powers up, but does not move

Corrective Maintenance

If the battery condition meter does not light up when you turn on the power:

!Check the harness connections. Make sure they are tight.

!Check the circuit breaker. Reset it if necessary.

!Check the battery connections.

If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up, contact your authorized Pride Provider.

Jazzy 614 Series

www.pridemobility.com

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Jazzy Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Public Streets and Roadways Outdoor Driving Surfaces Inclement Weather PrecautionsStationary Obstacles Steps, Curbs, etc Doors Stairs and EscalatorsElevators Lifts/Elevation ProductsBatteries Prescription Drugs/Physical Limitations TransfersElectromagnetic and Radio Frequency Interference EMI/RFI Alcohol/SmokingJazzy 614 Series I . Y O U R P O W E R C H a I RElectrical Components Jazzy 614 Series Power BaseJazzy 614 Series Electrical Components To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationYoumayneedthefollowingtomakecomfortadjustments Comfort AdjustmentsSeat Height and Seat Angle Adjustment O M F O R T a D J U S T M E N T SManual Recline Seatback Adjustment Seat Position AdjustmentTo adjust the recline angle To change the seat positionArmrest Width Adjustment Seatback Angle AdjustmentArmrest Angle Adjustment Armrest Height AdjustmentController Position Foot Platform Height AdjustmentTo extend the controller To change the controller positionTo adjust the foot platform depth Foot Platform Depth AdjustmentFoot Platform Angle Adjustment To adjust the foot platform angleBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Frequently Asked Questions FAQs Battery Break-inHow often must I charge the batteries? Why do my new batteries seem weak?Daily Use Infrequent UseHow should I store my power chair and its batteries? How can I ensure maximum battery life?What about public transportation? What about shipping?Should your power chair come in contact with water Care and MaintenanceTemperature I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksCleaning and Disinfection Disposal of Your Power ChairWheel Replacement StorageJazzy 614 Series Drive Wheel Battery ReplacementBattery Installation Corrective Maintenance When to See Your Authorized Pride Provider for ServiceTo replace the batteries I I . W a R R a N T Y Implied Warranties Service Checks and Warranty ServiceSpecifications P E N D I X I Specification SGroundclearance Turning Radius T E S Quality Control Jazzy 614 Series

614 2SP, 614 2S, 614 2HD specifications

Pride Mobility has established itself as a leading name in the mobility industry, and among its impressive lineup are the Pride Mobility 614 2HD, 614 2S, and 614 2SP power chairs. Each model is designed with specific features and technologies that cater to the diverse needs of users seeking enhanced mobility and independence.

The Pride Mobility 614 2HD, a heavy-duty model, boasts a robust construction capable of supporting users weighing up to 450 pounds. Its reinforced frame is complemented by its spacious seating system, ensuring user comfort for extended periods. Equipped with a powerful motor and a high-capacity battery, the 614 2HD facilitates smooth rides over various terrains, making it an ideal choice for both indoor and outdoor use. The model features advanced suspension systems, providing a level of stability and safety that is essential for users navigating uneven surfaces.

Next in line is the Pride Mobility 614 2S, designed for standard users who do not require the heavy-duty specifications of its counterpart. The 614 2S offers a balance of style, comfort, and functionality. It incorporates adjustable seating options and customizable controls, making it adaptable to individual preferences. The model is streamlined for ease of maneuverability, ensuring that users can navigate tight spaces with confidence. With a focus on efficiency, the 614 2S provides an excellent driving range on a single charge, making it convenient for day-to-day errands.

Lastly, the Pride Mobility 614 2SP takes versatility to another level. This model is engineered with a semi-powered tilt feature, which helps in optimizing weight distribution and enhancing user comfort. It also includes an easy-to-use joystick control for seamless navigation and precision handling. The 614 2SP is perfect for users who may require adjustments during their travels or those who prefer a more hands-on approach to their mobility solutions.

Across all models, key characteristics include user-friendly interfaces, sturdy construction, and advanced safety features such as anti-tip technology and customizable speed settings. The innovative design of these power chairs combines ergonomic seating and user-centric technology to improve overall quality of life. Whether you choose the 614 2HD, the 614 2S, or the 614 2SP, each model stands as a testament to Pride Mobility's commitment to enhancing independence, comfort, and mobility for users.
Top Page Image Contents