Sunrise Medical S-11 Transfers, Reaching or Leaning, To Reduce The Risk Of a Fall Or Tip-Over

Page 12

12

E n g l i s h

 

V I . G e n e r a l W a r n i n g s

To Reduce The Risk Of A Fall Or Tip-Over:

1.Consult your supplier for information on modifications authorized by Sunrise before you modify or adjust this chair.

NOTE– You may need to make additional changes to correct the center of balance.

2.Use extreme care until you know the balance points of this chair and how to avoid a fall or tip-over.

N.TRANSFERS

It is dangerous to transfer on your own. It requires good balance and agility. Be aware that there is a point during every transfer when the wheelchair seat is not below you. To avoid a fall:

1.Always turn off power before you transfer to or from your chair. If you fail to do so you may touch the joystick and cause your chair to move when you do not expect it.

2.Make sure motor locks are engaged. This keeps the chair from moving when you transfer.

3.Work with your health care professional to learn safe methods.

Learn how to position your body and how to support yourself during a transfer.

Have someone help you until you are sure you can do a safe transfer on your own.

4.Move your chair as close as you can to the seat you are transferring to. If possible, use a transfer board.

5.Rotate the front casters until they are as far forward as possible.

6.Be careful of the foot platform. If you can, remove or swing it out of the way.

Never stand on footrests when you transfer. Doing so may damage them or cause your chair to tip.

Make sure your feet do not “hang up” or get caught in the space between the footrests.

7.Make sure armrests do not interfere.

8.Transfer as far back onto the seat surface as you can. This will reduce the risk that you will miss the seat or fall.

O.REACHING OR LEANING

Reaching or leaning affects the center of balance of your chair. If done improper- ly, a fall or tip-over is likely. When in doubt, ask for help or use a device to extend your reach.

To Reduce the Risk of injury and/or Damage to the Chair:

1.Never reach or lean if you must shift your weight sideways or rise up off the seat.

2.Never reach or lean if you must move forward in your seat to do so. Always keep your buttocks in contact with the backrest.

3.Never reach with both hands (you may not be able to catch yourself to prevent a fall if you lose your balance).

4.Never try to pick up an object from the floor by reaching down between your knees.

5.Never put pressure on the foot platform while reaching. This may cause the chair to tip if you lean too far.

6.Never reach or lean over the top of the seat back. This may damage the backrest and cause you to fall.

IF YOU MUST REACH OR LEAN, DO SO AT YOUR OWN RISK.

Remember to:

1.Move your chair as close as you can to the object you wish to reach.

2.Rotate the front casters until they are as far forward as possible. This makes the chair more stable.

NOTE– To do this: Move your chair past the object you want to reach, then back up alongside it. Backing up will rotate the casters forward.

932108 Rev. C

Image 12
Contents Mode d’emploi et garantie N t r o d u c t i o n IntroductionSunrise Listens For Answers to Your QuestionsII. Table of Contents N t sVIII. SET UP, Adjustment & USE T a b l e o f C o n t e n t sI . Y o u r III. Your Chair and ITS PartsQuickie S-11 Choose the Right Chair & Safety Options Adjust Chair to Your AbilityT i c e R e a d B e f o r e U s e IV. NOTICE- Read Before USEWhat is EMI? EMI Electromagnetic InterferenceWhat Effect can EMI HAVE? Sources of EMIImmunity Level Report ALL Suspected EMI IncidentsWeight Limit Controller SettingsG e n e r a l W a r n i n g s Motor Vehicle Safety TerrainStreet USE Center of BalanceTransfers Reaching or LeaningIf YOU Must Reach or LEAN, do SO AT Your OWN Risk To Reduce The Risk Of a Fall Or Tip-OverDressing or Changing Clothes ObstaclesDriving in Reverse RAMPS, Slopes & SidehillsTo Reduce the Risk of a FALL, TIP-OVER or Loss of Control Ramps AT Home & WorkWheelchair Lifts Make sure ramps meet all Building Codes for your areaStairs EscalatorsI . W a r n i n g s C o m p o n e n t s & O p t i o n s VII. Warnings Components & OptionsON/OFF Switch Motor LocksPneumatic Tires Positioning BeltsWiring Upholstery FabricSuspension VIII. SET-UP, Adjustment & USE Tools YOU will NeedCHECK-OUT Footplate Adjustment I I . S e t u p , a d j u s t m e n t & U s eHanger Adapter Optional SWING-AWAY FootrestsElevating Legrest Optional Integral JoystickArmrests Adjustment Seat Height AdjustmentBackrest Seat Fore/Aft Adjustability Figure Seat RemovalRemove Shroud Replace ShroudPerformance Control Settings O p e r a t i n g I d eIX. Operating Guide Quickie Qtronix Programmer PAD OptionalJoystick Assembly Circuit BreakersO p e r a t i n g G u i d e Engage Motor LocksBattery Charger A t t e r i e sBatteries IntroductionConnecting Batteries in Battery Well Acid Burns Unsealed WET Cell BatteriesDisposing of Batteries Charging BatteriesXI. Maintenance CleaningBattery Maintenance M a i n t e n a n c eTo Repair or Replace a Tire Motor BrushesCorrosion For Answers To Questions Contact your supplierMaintenance Chart Ordering PartsCheck XII. Wiring Diagram Wiring Diagram Detail Integrated Control SystemI n XIII. Sunrise Limited Warranty I I . S u n r i s e L i m i t e d W a r r a n t y