Sunrise Medical S-11 instruction manual To Repair or Replace a Tire, Motor Brushes, Corrosion

Page 31

 

 

X

I

.

 

M

a

i

n

t

e

n

a

n c e

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

E n g l i s h

31

3. Corrosion:

Check battery terminals often for corrosion.

a. If corrosion is present, use a wire brush to clean the terminals.

NOTE– Always wear safety glasses and rubber gloves.

b.Use baking soda to neutralize acid.

c.Use petroleum jelly to re-grease the terminals after connecting cables to battery. (Completely cover the terminal nut and bolt, cable clip and any exposed cable with jelly).

4.For Answers To Questions: Contact your supplier.

E.PNEUMATIC TIRES

1.Do not use this chair if any of the tires are under-inflated or over-inflated.

2.Low pressure in a tire may cause the chair to veer to one side and result in loss of control.

3.An over-inflated tire may burst.

4.Never use a gas station pump to inflate a tire. Such pumps provide air at high volume, and may cause tire to burst.

1.Check for signs of wear and correct air pressure in pneumatic tires weekly.

2.For best performance, inflate tires to the same pressure level, as shown on the tire sidewall:

• 10" pneumatic drive wheels - 30 to 40 psi

3.Caution:

To prevent tire damage:

•Use a hand pump (or a low volume air pump) to inflate tires.

•Use a tire gauge to check pressure.

F. TO REPAIR OR REPLACE A TIRE

Residual air pressure in tires can cause severe injury. Make sure you release all air in tire before attempting to service or repair tires.

Drive Wheels:

a.Elevate and securely support chair so that wheel is off the ground. Release all air from tire (solid aluminum rim only).

b.Bend locking tab away from bolt.

c.Remove lock bolt.

d.Remove wheel from chair.

e.Make sure all air has been removed from tube.

f.Remove all bolts holding two halves of rim together (not applicable on solid alu- minum rim), and remove tire and solid insert.

g.Repair or replace inner tube (replace rim strip if necessary).

NOTE– Do not use pneumatic inner tube in tires with two-piece rims.

h.Reassemble the wheel.

Use a torque setting of 420 in.-lbs. to re-tighten bolts.

i.Install wheel on chair by replacing center lock bolt. Use a torque setting of 180 in.- lbs. to retighten bolts.

j.Inflate tire to proper pressure level (listed on tire sidewall).

G. MOTOR BRUSHES

Check the motor brushes every four (4) months for wear. The brushes should be clean and shiny. Replace worn or blackened brushes.

932108 Rev. C

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Mode d’emploi et garantie For Answers to Your Questions N t r o d u c t i o nIntroduction Sunrise ListensN t s II. Table of ContentsT a b l e o f C o n t e n t s VIII. SET UP, Adjustment & USEIII. Your Chair and ITS Parts I . Y o u rQuickie S-11 IV. NOTICE- Read Before USE Choose the Right Chair & Safety OptionsAdjust Chair to Your Ability T i c e R e a d B e f o r e U s eSources of EMI What is EMI?EMI Electromagnetic Interference What Effect can EMI HAVE?Report ALL Suspected EMI Incidents Immunity LevelController Settings Weight LimitG e n e r a l W a r n i n g s Center of Balance Motor Vehicle SafetyTerrain Street USETo Reduce The Risk Of a Fall Or Tip-Over TransfersReaching or Leaning If YOU Must Reach or LEAN, do SO AT Your OWN RiskRAMPS, Slopes & Sidehills Dressing or Changing ClothesObstacles Driving in ReverseMake sure ramps meet all Building Codes for your area To Reduce the Risk of a FALL, TIP-OVER or Loss of ControlRamps AT Home & Work Wheelchair LiftsEscalators StairsVII. Warnings Components & Options I . W a r n i n g s C o m p o n e n t s & O p t i o n sPositioning Belts ON/OFF SwitchMotor Locks Pneumatic TiresUpholstery Fabric WiringSuspension Tools YOU will Need VIII. SET-UP, Adjustment & USECHECK-OUT I I . S e t u p , a d j u s t m e n t & U s e Footplate AdjustmentIntegral Joystick Hanger Adapter OptionalSWING-AWAY Footrests Elevating Legrest OptionalSeat Height Adjustment Armrests AdjustmentBackrest Replace Shroud Seat Fore/Aft Adjustability FigureSeat Removal Remove ShroudQuickie Qtronix Programmer PAD Optional Performance Control SettingsO p e r a t i n g I d e IX. Operating GuideCircuit Breakers Joystick AssemblyEngage Motor Locks O p e r a t i n g G u i d eIntroduction Battery ChargerA t t e r i e s BatteriesAcid Burns Unsealed WET Cell Batteries Connecting Batteries in Battery WellCharging Batteries Disposing of BatteriesM a i n t e n a n c e XI. MaintenanceCleaning Battery MaintenanceFor Answers To Questions Contact your supplier To Repair or Replace a TireMotor Brushes CorrosionOrdering Parts Maintenance ChartCheck Wiring Diagram Detail Integrated Control System XII. Wiring DiagramI n I I . S u n r i s e L i m i t e d W a r r a n t y XIII. Sunrise Limited Warranty
Top Page Image Contents