Quantum 610 owner manual Seat Installation, To install the seat

Page 22

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached to the power base with the Universal Mount- ing System (UMS). The UMS consists of universal parts that may be attached to any medium-back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11. If your power chair is equipped with a Synergy Seating System or a Syn- ergy TRU-Balance Power Positioning System, refer to the information provided in separate manuals.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

To install the seat:

1.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

2.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

3.Flip the seat latch safety down. See figure 11.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

REAR

EXTRUSION

SEAT

LATCH

SAFETY

REAR TRAPEZE

BAR

Figure 11. Universal Mounting System (FLIGHT Shown)

4.Install the controller and route the cable to the back of the power base. See figure 12.

5. Loosen the rear shroud fasteners counterclockwise one- quarter turn and remove the rear shroud. See figure 6.

6. Plug the controller connector into the power base. See figure 7.

7. Reinstall the rear shroud. Turn the rear shroud fasteners clockwise one-quarter turn. See figure 6.

8. Route the controller cable so that it cannot be pinched in the seat hinge.

9. Secure the controller cable to the armrest receiver with wire ties. See figure 13.

Figure 12. Remote Plus Controller Routed on a Synergy

Seat

22

www.quantumrehab.com

Quantum 610

Image 22

Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Preventing Unintended Movement Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingRemovable Parts Prescription Drugs/Physical Limitations BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R QuantumQuantum 610 Specifications Quantum 610 Power Base Electrical ComponentsCharger Inhibit Connector Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatPower Seat Option Installation To install the power seatO M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment Can also change the seat base angle dumpManual Recline Seatback Adjustment Seatback Angle AdjustmentSeat Position Armrest Angle Adjustment Armrest Width AdjustmentController Position Foot Platform Depth Adjustment Foot Platform Height AdjustmentFoot Platform Angle Adjustment Elevating Leg Rests Swing-away FootrestsHeavy Duty Drop-in Leg Rests Multi-Axis Foot Plates Power Elevating Seat Optional To change the seat height through toggle switchBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries To charge the batteries using the optional onboard charger To charge the batteries using the off-board chargerBattery Break-in Frequently Asked Questions FAQs How should I store my power chair and its batteries? Why do my new batteries seem weak?How can I ensure maximum battery life? What about public transportation?Joystick I . O P E R a T I O NFlight Controller KeypadOn/Off Key Battery Condition MeterLock Mode To lock the Flight controllerError Code Probable Cause Possible Solution Sleep Mode If EnabledError Codes Speed KeysVSI Electronic Controller VSI consistsRed, yellow, and green lights lit Batteries charged Speed/Profile KeysActuator Connector Optional Motor ConnectorsBattery Connector Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Charger Inhibit Connector OptionalThermal Rollback Remote Plus Remote Plus ControllerRemote Plus consists of the following Mode Key Speed Settings To select a speed settingPower Accessories Optional Right/Left Turn Indicator Keys OptionalPower Accessory Indicator Optional Sleep ModeRemote Plus Error Codes Microdrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleDrive Profile Selection To select a profile settingSpeed Adjustment To change the speedFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksCleaning Instructions Wheel Replacement StorageBattery Replacement To replace the batteriesBattery Installation When to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S Quality Control Quantum

Related manuals

Manual 24 pages 41.97 Kb