Quantum 610 Seat Position, Seatback Angle Adjustment, Manual Recline Seatback Adjustment

Page 25

		V . C O M F O R T A D J U S T M E N T S
	14.	Reconnect the controller connector(s) to the power base.
	15.	Reinstall the rear shroud and tighten the fasteners.
	Seat Position
	You can move the seat forward or rearward by changing
	the extrusion mounting position.
	To change the position:
	1.	Turn off the power to the controller.
	2.	Unlock the rear shroud fasteners and remove the rear
		shroud. See figure 6.
	3.	Unplug the controller connector(s) from the power base.
	4.	Remove the seat from the power base.
	5.	Remove both extrusions from the bottom of the seat.
	6.	Reposition the extrusions on a different set of mounting
		holes. You must move both extrusions the same number
		of holes either forward or backwards. See figure 17.
	7.	Fasten the extrusions back onto the bottom of the seat.
	8.	Reinstall the seat.	Figure 17. Seat Position Adjustment
	9.	Reconnect the controller.	Figure 17. Seat Position Adjustment
	9.	Reconnect the controller.
	10.	Reinstall the rear shroud and tighten the fasteners.

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.

To adjust the seatback angle:

1.Remove the adjusting screws from each seat hinge. See figure 18.

2.Set the seatback at the desired angle.

3.Reinstalltheadjustingscrewstoeachseathingeandtighten.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base.

To adjust the recline angle:

1.Pull up on the seatback release lever.

2.Lean forward or backwards to the desired position.

3.Release the lever.

ARMREST ANGLE ADJUSTING SCREW

JAM

NUTS

SEATBACK

ANGLE

ADJUSTING

SCREW

ARMREST KNOB

Figure 18. Seatback Angle Adjustment

Quantum 610

www.quantumrehab.com

25

Image 25

Contents Page F E T Y G U I D E L I N E S III N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Information ExchangeMy Quantum Rehab Specialist Pride Owners ClubS a F E T Y Product Safety SymbolsS a F E T Y Modifications Pre-Ride Safety CheckTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Preventing Unintended Movement Outdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc Stairs and EscalatorsDoors TransfersElevators Lift/Elevation ProductsMotor Vehicle Transport Inclement Weather PrecautionsPositioning Belts Reaching and BendingRemovable Parts Prescription Drugs/Physical Limitations BatteriesAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI Quantum I . Y O U R P O W E R C H a I RQuantum 610 Specifications Electrical Components Quantum 610 Power BaseCharger Inhibit Connector To engage or disengage the drive motors Manual Freewheel LeversA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationTo install the power seat Power Seat Option InstallationSeat Height and Seat Angle Adjustment Comfort AdjustmentsO M F O R T a D J U S T M E N T S Can also change the seat base angle dumpManual Recline Seatback Adjustment Seatback Angle AdjustmentSeat Position Armrest Angle Adjustment Armrest Width AdjustmentController Position Foot Platform Depth Adjustment Foot Platform Height AdjustmentFoot Platform Angle Adjustment Elevating Leg Rests Swing-away FootrestsHeavy Duty Drop-in Leg Rests Multi-Axis Foot Plates To change the seat height through toggle switch Power Elevating Seat OptionalBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries To charge the batteries using the optional onboard charger To charge the batteries using the off-board chargerBattery Break-in Frequently Asked Questions FAQs How can I ensure maximum battery life? Why do my new batteries seem weak?How should I store my power chair and its batteries? What about public transportation?Flight Controller I . O P E R a T I O NJoystick KeypadLock Mode Battery Condition MeterOn/Off Key To lock the Flight controllerError Codes Sleep Mode If EnabledError Code Probable Cause Possible Solution Speed KeysVSI consists VSI Electronic ControllerSpeed/Profile Keys Red, yellow, and green lights lit Batteries chargedBattery Connector Motor ConnectorsActuator Connector Optional Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Charger Inhibit Connector OptionalThermal Rollback Remote Plus Remote Plus ControllerRemote Plus consists of the following To select a speed setting Mode Key Speed SettingsPower Accessory Indicator Optional Right/Left Turn Indicator Keys OptionalPower Accessories Optional Sleep ModeRemote Plus Error Codes Microdrive Controller consists Microdrive ControllerActuator Indicator Profile and Speed IndicatorDisplay Pad Joystick Interface ModuleSpeed Adjustment To select a profile settingDrive Profile Selection To change the speedFlashing Lights Diagnosis Solution Should your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Monthly ChecksStorage Cleaning Instructions Wheel ReplacementTo replace the batteries Battery ReplacementBattery Installation Corrective Maintenance When to See Your Quantum Rehab Specialist for ServiceW a R R a N T Y Warranty Exclusions Reconditioned Units WarrantyService Checks and Warranty Service Exclusions also include components with damage caused byT E S Quality Control Quantum

Related manuals

Manual 24 pages 41.97 Kb