Quantum 610 owner manual Armrest Width Adjustment, Armrest Angle Adjustment, Controller Position

Page 26

Figure 20. Underside of Armrest (Contour Seat)

	V . C O M F O R T A D J U S T M E N T S
Armrest Width Adjustment
Youcanchangeeacharmrest’swidthindependentlyoftheother.
NOTE: Changing the armrest width may increase the		FOOT PLATFORM
overall width of your power chair.		FOOT PLATFORM
overall width of your power chair.		RETAINING PIN	SECUREMENT NUT
To change the armrest width:
1.	Locate the two armrest knobs on each side of the arm-	FOOT
	rest receiver bracket. See figure 18.	FOOT
	rest receiver bracket. See figure 18.	PLATFORM
2.	Loosen the knobs.	BRACKET
3.	Slide the armrests in or out to the desired width.
4.	Tighten the knobs.
Armrest Angle Adjustment		QUICK
To change the armrest angle:		QUICK
1.	Lift the armrest straight up so that it is perpendicular to	RELEASE
1.	Lift the armrest straight up so that it is perpendicular to	FASTENERS
	the floor. See figure 18.	SETSCREW
2.	Loosen the jam nuts.
3.	Turn the adjusting screw clockwise to lower the front	Figure 19. Foot Platform Adjustment
	of the armrest, or turn the adjusting screw counterclock-
	wise to raise the front of the armrest.
4.	Tighten the jam nuts to lock the adjusting screw into	SETSCREW
	place.	SETSCREW
	place.

Controller Position

You can position the controller for either left-hand or right- hand use.

WARNING! Do not place the controller cable so that it can be pinched in the seat frame or the power base frame.

To change the controller position:

1. Turn off the power to the controller.

2.Turn the rear shroud fasteners counterclockwise one- quarter turn. See figure 6.

3.Remove the rear shroud.

4.Unplug the controller connector(s) from the power base.

5.Cutthewiretie(s)securingthecontrollercabletothearmrest. See figure 6.

6.Loosen the mounting screws in the mounting block. See figure 21.

7.Move the controller mounting block and controller to the other armrest and tighten the mounting screws.

NOTE: For contour seats, loosen the setscrew on the underside of both armrests, transfer the controller, and tighten the setscrews. See figure 20.

8.Route the controller cable to the back of the power base and plug in the controller. See figure 12.

9.Use wire ties to secure the controller cable to the seat frame. See figure 13.

26

www.quantumrehab.com

Quantum 610

Image 26

Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsIncline Information Weight LimitationsTire Inflation Public Streets and Roadways Preventing Unintended Movement Braking InformationCornering Information Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingAlcohol BatteriesRemovable Parts Prescription Drugs/Physical Limitations Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R QuantumQuantum 610 Specifications Quantum 610 Power Base Electrical ComponentsCharger Inhibit Connector Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatPower Seat Option Installation To install the power seatO M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment Can also change the seat base angle dumpSeat Position Seatback Angle AdjustmentManual Recline Seatback Adjustment Controller Position Armrest Width AdjustmentArmrest Angle Adjustment Foot Platform Angle Adjustment Foot Platform Height AdjustmentFoot Platform Depth Adjustment Heavy Duty Drop-in Leg Rests Swing-away FootrestsElevating Leg Rests Multi-Axis Foot Plates Power Elevating Seat Optional To change the seat height through toggle switchCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Battery Break-in To charge the batteries using the off-board chargerTo charge the batteries using the optional onboard charger Frequently Asked Questions FAQs How should I store my power chair and its batteries? Why do my new batteries seem weak?How can I ensure maximum battery life? What about public transportation?Joystick I . O P E R a T I O NFlight Controller KeypadOn/Off Key Battery Condition MeterLock Mode To lock the Flight controllerError Code Probable Cause Possible Solution Sleep Mode If EnabledError Codes Speed KeysVSI Electronic Controller VSI consistsRed, yellow, and green lights lit Batteries charged Speed/Profile KeysActuator Connector Optional Motor ConnectorsBattery Connector Actuator Keys and Actuator Lights For Optional EquipmentThermal Rollback Charger Inhibit Connector OptionalVSI Error Codes Remote Plus consists of the following Remote Plus ControllerRemote Plus Mode Key Speed Settings To select a speed settingPower Accessories Optional Right/Left Turn Indicator Keys OptionalPower Accessory Indicator Optional Sleep ModeRemote Plus Error Codes Microdrive Controller Microdrive Controller consistsDisplay Pad Profile and Speed IndicatorActuator Indicator Joystick Interface ModuleDrive Profile Selection To select a profile settingSpeed Adjustment To change the speedFlashing Lights Diagnosis Solution Temperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksCleaning Instructions Wheel Replacement StorageBattery Replacement To replace the batteriesBattery Installation When to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S Quality Control Quantum

Related manuals

Manual 24 pages 41.97 Kb