Pride Mobility Jet2HD I I . B a T T E R I E S a N D C H a R G I N G, Batteries and Charging

Page 28

V I I I . B A T T E R I E S A N D C H A R G I N G

BATTERIES AND CHARGING

The Jet 2 HD uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable. Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.

WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Wash hands after handling.

Charging the Batteries

The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power chair’s performance by charging the batteries safely, quickly, and easily. The battery charging system con- sists of the onboard battery charger, the charger circuit fuse, and the ammeter. The ammeter indicates the rate of charge necessary to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter and the charger are only functional when the charger power cord is plugged into an electri- cal outlet. The charger circuit has an ATO fuse that protects the ammeter.

WARNING! You must recharge your power chair’s batteries with the supplied onboard battery charger. Do not use an automotive-type battery charger.

PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure to heed could result in personal injury and/or property damage.

PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger directly into a properly wired standard electrical outlet.

To charge the batteries using the onboard charger:

1.Position the rear of your power chair close to a standard electrical outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power Chair.”

3.Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.

NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is plugged into an electrical outlet.

4.We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops to 0.

NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to 0 amps as the batteries charge.

5.When the batteries are fully charged, the needle vibrates on or about the 0 mark on the ammeter. Discon- nect the charger power cord, wind up the cord, and store it in a safe place.

28

www.pridemobility.com

Jet 2 HD

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S B L E O F C O N T E N T S IIISafety N T R O D U C T I O NPURCHASER’S Agreement Information ExchangePride Owners Club My Authorized Pride ProviderS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Freewheel Mode Outdoor Driving SurfacesStationary Obstacles Steps, Curbs, etc Stairs and EscalatorsTransfers Object you are transferring ontoDoors ElevatorsInclement Weather Precautions Motor Vehicle TransportPositioning Belts Reaching and BendingAlcohol BatteriesElectromagnetic and Radio Frequency Interference EMI/RFI S a F E T Y I . Y O U R P O W E R C H a I R JET 2 HDSpecifications Electronics Tray Electronics TrayTo engage or disengage the freewheel feature Freewheel LeversSeat Installation To install the seatController Installation To install the controllerComfort Adjustments Seat Height AdjustmentO M F O R T a D J U S T M E N T S To change the seat heightArmrest Width Adjustment Armrest Height Adjustment OptionalArmrest Angle Adjustment Controller Extension AdjustmentSwing-away Footrests Foot Platform Angle AdjustmentElevating Leg Rests To adjust the ELR angle To adjust the ELR lengthAnti-Tip Wheel Adjustment To adjust the anti-tip wheelsD I S a S S E M B L Y Seat RemovalTo remove the seat Body Shroud RemovalI . O P E R a T I O N VSI Electronic ControllerVSI consists JoystickBattery Condition Meter On/Off KeySystem OK Speed/Profile KeysController Connector Horn KeyLocking/Unlocking the VSI Off-board Charger/Programming SocketVSI Error Codes Charger Inhibit ConnectorThermal Rollback To charge the batteries using the onboard charger I I . B a T T E R I E S a N D C H a R G I N GBatteries and Charging Charging the BatteriesBattery Break-in Frequently Asked Questions FAQsWhat type of battery should I use? Why do my new batteries seem weak?How can I ensure maximum battery life? How can I get maximum range or distance per charge?What about public transportation? How should I store my power chair and its batteries?What about shipping? Care and Maintenance Should your power chair come in contact with waterTemperature C a R E a N D M a I N T E N a N C EDaily Checks Weekly ChecksTo check the brakes Monthly ChecksBattery Replacement Yearly ChecksTo replace the batteries StorageCleaning Instructions Wheel Replacement Drive Wheel RemovalWhen to See Your Authorized Pride Provider for Service Corrective MaintenanceA R R a N T Y Service Checks and Warranty Service Implied WarrantiesPower Chairs
Top Page Image Contents