Pride Mobility Revo C a R E a N D M a I N T E N a N C E, Tire Pressure, Wheel Replacement

Page 37

X I . C A R E A N D M A I N T E N A N C E

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance.

TIRE PRESSURE

!If equipped with pneumatic tires, always maintain a proper 30-35 psi tire pressure.

WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure in pneumatic tires at all times may result in tire and/or wheel failure, causing serious personal injury and/or damage to your scooter.

!Regularly inspect your scooter’s tires for signs of wear.

WHEEL REPLACEMENT

If your scooter is equipped with pneumatic tires and you have a flat tire, you can have the tube replaced. If your scooter is equipped with a solid tire insert, either the solid insert or the entire wheel must be replaced depending on model. Contact your authorized Pride Provider for information regarding replacement wheels for your scooter.

WARNING! Prevent personal injury! Completely deflate pneumatic tires before dismantling the rim or attempting repair.

WARNING! When changing a tire, remove only the center lug nut, then remove the tire. If any further disassembly is required, deflate the tire completely or it may explode, possibly resulting in personal injury.

EXTERIOR SURFACES

Bumpers and tires can benefit from an occasional application of a rubber or vinyl conditioner.

WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tire tread. They will become dangerously slippery and result in personal injury and/or damage to your scooter.

CLEANING AND DISINFECTION

!Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter. Avoid using products that may scratch the surface of your scooter.

!If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your product before application.

WARNING! Prevent personal injury and product damage! Follow all safety instructions for the proper use of the disinfectant before applying it to your product.

Revo

www.pridemobility.com

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Ultimate In Style & Performance F E T Y G U I D E L I N E S III N T E N T SN T R O D U C T I O N SafetyPURCHASER’S Agreement Information ExchangeS a F E T Y Product Safety SymbolsModifications GeneralRemovable Parts S a F E T Y Weight Limitations PRE-RIDE Safety CheckTire Inflation Incline InformationMaximum Recommended Incline Angles With Oxygen Tank Braking Information Cornering InformationCorrect Curb Approach Outdoor Driving SurfacesFreewheel Mode Inclement Weather PrecautionsStairs and Escalators Doors Battery Disposal and RecyclingElevators LIFT/ELEVATION ProductsReaching and Bending Motor Vehicle TransportPrescription DRUGS/PHYSICAL Limitations Positioning BeltsAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . E M I / R FStandard Seating Specification SScooter Dimensions Tiller Console O U R S C O O T E RRear Section Horn ButtonBattery Packs OFF-BOARD Battery Charger Voltage Switch Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Charging the Batteries on the Scooter Charging the Batteries OFF of the Scooter Follow these easy steps to charge your batteries safelyTo charge the batteries off of the scooter How does the charger work? Frequently Asked QuestionsWhat if my scooter’s batteries won’t charge? How often must I charge the batteries?Battery Replacement What type and size of battery should I use?What about public transportation? Why do my new batteries seem weak?I . O P E R a T I O N PRE-RIDE Adjustments and ChecksBefore Getting Onto Your Scooter Getting Onto Your ScooterGetting OFF of Your Scooter Power Down Timer FeatureArmrest Width Adjustment Tiller Angle AdjustmentI I . C O M F O R T a D J U S T M E N T S Seat RotationSeat Height Adjustment FRONT-TO-BACK Seat AdjustmentD I S a S S E M B L Y a N D a S S E M B L Y DisassemblyToggle Latch Release Assembly Diagnostic Flash Codes A S I C TroubleshootingWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? Cleaning and Disinfection Wheel ReplacementC a R E a N D M a I N T E N a N C E Tire PressureWiring Harnesses Battery Terminal ConnectionsAxle Bearings and the MOTOR/TRANSAXLE Assembly Fuse ReplacementNylon Lock NUT Replacement Light Bulb ReplacementStoring Your Scooter Disposal of Your ScooterI . W a R R a N T Y Implied Warranties Service Checks and Warranty ServiceT E S INFMANU2427
Top Page Image Contents