Pride Mobility Jazzy 1170XL To adjust the ELR length, To adjust the ELR angle, Anti-tip Wheels

Page 26

V . C O M F O R T A D J U S T M E N T S

To adjust the ELR length:

1.Remove the two adjustment screws from the side of each leg rest extension. See figure 23.

2.Slide the leg rest up or down to the desired length.

3.Reinstall the two adjustment screws.

To adjust the ELR angle:

1.Push down release lever B. See figure 23.

2.Move the leg rest to the desired angle.

Anti-tip Wheels

The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are preset for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if either of the following occur:

νWhen coming to a stop, your power chair tips forward excessively.

νThe anti-tip wheels constantly rub the ground.

WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip wheel height! Changing the anti-tip wheel height affects handling under deceleration!

WARNING! The higher you raise the anti-tip wheels, the more you increase your power chair’s tendency to tilt forward when coming to a stop. You can compensate for this by having your authorized Pride Provider make a small adjustment to the pre- programmed deceleration setting in the controller or by moving the seat assembly farther to the rear of your power chair.

Figure 24. Anti-Tip Bracket (Inner Locknut)

To adjust the anti-tip wheels:

1.Place a wrench on the inner locknut of the anti- tip bracket located right after the shock strut. See figure 24.

2.Turn the locknut counterclockwise to loosen the cam.

3.Place your wrench on the adjustable cam located on the other side of the locknut.

	4.	To adjust the anti-tip upward, turn the cam coun-
		terclockwise. To adjust the anti-tip downward, turn
		the cam clockwise. See figure 25.	Figure 25. Anti-Tip Wheel Adjustment (Cam)
	5.	Tighten the locknut.	Figure 25. Anti-Tip Wheel Adjustment (Cam)
	5.	Tighten the locknut.

NOTE: Each drive tire must have 35 psi in order for the anti-tip wheels to be properly adjusted.

26

www.pridemobility.com

Jazzy 1170XL

Image 26

Contents Exeter, PA St. Catharines, on F E T Y G U I D E L I N E S N T E N T S Information Exchange N T R O D U C T I O NPURCHASER’S Agreement Pride Owners Club My authorized Pride Provider isModifications Pre-Ride Safety CheckS a F E T Y Incline Information Weight LimitationsTire Inflation Braking Information Maximum Safe Angle Ascending and DescendingOutdoor Driving Surfaces Freewheel ModeCornering Information Stationary Obstacles Steps, Curbs, etcElevators Public Streets and Roadways Stairs and EscalatorsDoors Lift/Elevation ProductsPositioning Belts Motor Vehicle TransportTransfers Batteries Inclement Weather PrecautionsReaching and Bending Preventing Unintended MovementPrescription Drugs/Physical Limitations AlcoholI . Y O U R P O W E R C H a I R Jazzy 1170XLBased on user weight and terrain Jazzy 1170XL Power Base Shroud Removed Electronics Tray Active-Trac SystemManual Freewheel Levers To engage or disengage the dual freewheel featureTo engage or disengage the single freewheel feature Initial Assembly A S S E M B L YSeat Installation To install the seatPower Elevating Seat Actuator You may need the following to make comfort ad- justments Seat Height and Seat Angle AdjustmentO M F O R T a D J U S T M E N T S Seat base angle dumpSeatback Angle Adjustment Reclining Seat AdjustmentTo adjust the reclining seat To adjust the seatback angleFootrest Angle Adjustment Armrest Angle Adjustment To change the armrest angleFootrest Height Adjustment To adjust the footrest angleTo change the controller position To adjust the SFR lengthController Position Swing-away FootrestsTo adjust the anti-tip wheels To adjust the ELR lengthTo adjust the ELR angle Anti-tip WheelsTo operate the power elevating seat through toggle switch Power Elevating Seat OptionPower Elevating Seat Operation Batteries and Charging To charge the batteries using an onboard battery chargerB a T T E R I E S a N D C H a R G I N G Charging the BatteriesCan I use a different battery charger? To charge the batteries using an off-board battery chargerFrequently Asked Questions FAQs How does the charger work? How often must I charge the batteries?Infrequent Use Why do my new batteries seem weak?Daily Use How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?VSI consists I . O P E R a T I O NVSI Controller JoystickSpeed/Profile Keys Battery Condition MeterOn/Off Key Horn Key Actuator ConnectorController Connector Locking/Unlocking the VSIThermal Rollback Charger Inhibit ConnectorVSI Error Codes Remote Plus Controller Remote Plus Master RemoteLight Key On/Off Key On/off keys toggles the system power onRight/Left Turn Indicator Keys Hazard KeyPower Accessories Speed SettingsTo select a speed setting Remote Plus Error Codes Power ModuleSleep Mode Controller Communications CableFlashing Diagnosis Solution Lights Europa Controller consists Out Of Neutral At Power UpEuropa Controller Magnetic Locking Area To enable the lockout systemSystem Status Light Battery Saver Feature To change the drive mode programDrive Mode and Actuator Display also Remote Status Display Drive Program Select KeySleep Mode If Enabled Europa Error CodesTemperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Yearly Checks Cleaning Instructions Tire/Wheel ReplacementMonthly Checks StorageBattery Replacement To replace the batteriesWhen to See Your Authorized Pride Provider for Service Corrective MaintenanceW a R R a N T Y Exclusions also include components with damage caused by Warranty ExclusionsService Checks and Warranty Service Implied WarrantiesQuality Control Model 1170 XL Pride keeps a more detailed report on file at the factory