Pride Mobility INFMANU4206 manual Batteries, Anti-Tip Wheels, Motor/Transaxle Assembly

Page 22

I I I . Y O U R S C O O T E R

Batteries

The batteries store electrical energy that powers your scooter. See IV. “Batteries and Charging” for information on how to charge your scooter batteries.

Anti-Tip Wheels

The anti-tip wheels are an integral and important safety feature of your scooter. They are bolted to the frame at the rear of the scooter.

PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that is not authorized by Pride.

WARNING! The anti-tip wheels may cause interference with the smooth transition of your Travel Scooter when ascending or descending a curb. Contact your authorized Pride Dealer for more information.

Motor/Transaxle Assembly

The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your scooter’s batteries into the controlled mechanical energy that drives the scooter’s wheels.

Manual Freewheel Lever

Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.

1.Remove the key from the key switch.

2.Push forward on the manual freewheel lever to disable the drive system and the brake system. This will enable you to push the scooter.

3.Pull back on the manual freewheel lever to reengage the drive and the brake systems and take your scooter out of freewheel mode.

WARNING! When your scooter is in freewheel mode, the braking system is disengaged. Disengage the drive motors only on a level surface.

Ensure the key is removed from the key switch.

Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on a scooter to do this.

After you have finished pushing your scooter, always return it to the drive mode to lock the brakes.

NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in the “on” position, the scooter will not run until the manual freewheel lever is pushed backward and the key is turned to the “off” position, then back to the “on” position.

Safety Flag Bracket

An accessory bracket for installing an optional safety flag is mounted near each anti-tip wheel. See figure 7. To install the flag, the supplied L-shaped hex key is needed.

To install the safety flag:

1.Remove the cap from the top of the bracket.

2.Loosen the setscrew with the supplied L-shaped hex key.

3.Insert the flag pole into the opening.

4.Tighten the setscrew to complete installation.

22

www.pridemobility.com

Victory Sport

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Victory Sport F E T Y G U I D E L I N E S N T E N T S PURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y General Removable Parts PRE-RIDE Safety CheckModifications Tire Inflation Weight LimitationsIncline Information S a F E T Y Cornering Information Your scooter is equipped with these powerful brake systemsBraking Information Outdoor Driving Surfaces Correct Curb ApproachStairs and Escalators Inclement Weather PrecautionsFreewheel Mode DoorsLIFT/ELEVATION Products Battery Disposal and RecyclingElevators BatteriesReaching and Bending Motor Vehicle TransportGetting Onto and OFF of Your Scooter Positioning BeltsPrescription DRUGS/PHYSICAL Limitations Flammability PrecautionsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R S C O O T E R Tiller ConsoleHazard Lights Switch Turn Signal ButtonsLights Switch Hi-Low SwitchElectrical System Fuses Off-board Charger PortRear Components Batteries Motor/Transaxle AssemblySafety Flag Bracket Anti-Tip WheelsMain Circuit Breaker Reset Button Securing the ScooterBatteries and Charging Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Charging Your BatteriesHow does the charger work? Frequently Asked QuestionsFollow these easy steps to change your batteries safely Can I use a different charger?How often must I charge the batteries? How can I ensure maximum battery life?What type and size of battery should I use? How can I get maximum range or distance per charge?You may need the following to change your batteries How do I change a battery in my scooter?To change the batteries in your scooter Why do my new batteries seem weak? Battery Removal/InstallationWhat about public transportation? Before Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Getting Onto Your ScooterPower Down Timer Feature Getting OFF of Your ScooterC O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentSeatback Adjustment Mirror PositionSeat Rotation Adjustment Seat Height AdjustmentArmrest Angle Adjustment FRONT-TO-BACK Seat AdjustmentPositioning Belt Optional To adjust the positioning belt for operator comfortTo release the positioning belt Disassembly I . D I S a S S E M B L Y a N D a S S E M B L YAssembly Frame SeparationDiagnostic Fault Codes I I . B a S I C TroubleshootingWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Motor Brushes Axle Bearings and the MOTOR/TRANSAXLE AssemblyWheel Replacement CONSOLE, CHARGER, and Rear ElectronicsEvent a fuse should cease to work Fuse ReplacementNylon Lock NUT Replacement Storing Your ScooterT E S Page INFMANU4206
Top Page Image Contents