Pride Mobility INFMANU4206 Axle Bearings and the MOTOR/TRANSAXLE Assembly, Wheel Replacement

Page 40

I X . C A R E A N D M A I N T E N A N C E

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY

These items are all prelubricated, sealed, and require no subsequent lubrication.

WHEEL REPLACEMENT

If your scooter is equipped with pneumatic tires and you have a flat tire, you can have the tube replaced. If your scooter is equipped with a solid tire insert, either the solid insert or the entire wheel must be replaced depending on the model. Contact your authorized Pride Provider for information regarding replacement wheels for your scooter.

WARNING! Wheels on your scooter should only be serviced/replaced by a qualified technician.

WARNING! Completely deflate pneumatic tires before dismantling the rim or attempting repair.

WARNING! Be sure that the key is removed from the key switch and the scooter is not in freewheel mode before performing this procedure repair.

WARNING! When changing a pneumatic tire, remove only the lug nuts, then remove the wheel. If any further disassembly is required, deflate the tire completely or it may explode.

Follow these easy steps for a quick and safe repair for solid tires:

1.Remove the key from the key switch and ensure your scooter is not in freewheel mode.

2.Elevate the side of the scooter of which you are removing the tire. Place wooden blocks under the frame to elevate the scooter.

3.Remove the wheel cap, drive wheel nut, and washer from the axle. See figure 25.

4.Pull the wheel off the axle.

5.Slide the new wheel onto the axle. Make sure the axle key is in the axle slot.

WARNING! Failure to ensure that the axle key is properly installed into the axle slot when mounting the wheel can result in electronic brake failure, personal injury and/ or product damage.

 

AXLE SLOT

WASHER

AXLE KEY

WHEEL

DRIVE WHEEL NUT

CAP

 

Figure 25. Solid Tire Wheel Removal

6. Reinstall the drive wheel nut and washer onto the axle and tighten.

WARNING! Make sure that both the nut and washer are reinstalled and tightened properly.

7.Reinstall the wheel cap.

8.Remove the blocks from beneath the scooter.

MOTOR BRUSHES

The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for wear by your authorized Pride Provider.

CONSOLE, CHARGER, AND REAR ELECTRONICS

Keep these areas free of moisture.

Allow these areas to dry thoroughly if they have been exposed to moisture before operating your scooter again.

40

www.pridemobility.com

Victory Sport

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Victory Sport F E T Y G U I D E L I N E S N T E N T S Safety N T R O D U C T I O NPURCHASER’S Agreement Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y General Removable Parts PRE-RIDE Safety CheckModifications Tire Inflation Weight LimitationsIncline Information S a F E T Y Cornering Information Your scooter is equipped with these powerful brake systemsBraking Information Outdoor Driving Surfaces Correct Curb ApproachInclement Weather Precautions Freewheel ModeStairs and Escalators DoorsBattery Disposal and Recycling ElevatorsLIFT/ELEVATION Products BatteriesMotor Vehicle Transport Getting Onto and OFF of Your ScooterReaching and Bending Positioning BeltsPrescription DRUGS/PHYSICAL Limitations Flammability PrecautionsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R S C O O T E R Tiller ConsoleTurn Signal Buttons Lights SwitchHazard Lights Switch Hi-Low SwitchElectrical System Fuses Off-board Charger PortRear Components Motor/Transaxle Assembly Safety Flag BracketBatteries Anti-Tip WheelsMain Circuit Breaker Reset Button Securing the ScooterReading Your Battery Voltage B a T T E R I E S a N D C H a R G I N GBatteries and Charging Charging Your BatteriesFrequently Asked Questions Follow these easy steps to change your batteries safelyHow does the charger work? Can I use a different charger?How can I ensure maximum battery life? What type and size of battery should I use?How often must I charge the batteries? How can I get maximum range or distance per charge?You may need the following to change your batteries How do I change a battery in my scooter?To change the batteries in your scooter Why do my new batteries seem weak? Battery Removal/InstallationWhat about public transportation? PRE-RIDE Adjustments and Checks P E R a T I O NBefore Getting Onto Your Scooter Getting Onto Your ScooterPower Down Timer Feature Getting OFF of Your ScooterTiller Angle Adjustment Seatback AdjustmentC O M F O R T a D J U S T M E N T S Mirror PositionSeat Height Adjustment Armrest Angle AdjustmentSeat Rotation Adjustment FRONT-TO-BACK Seat AdjustmentPositioning Belt Optional To adjust the positioning belt for operator comfortTo release the positioning belt Disassembly I . D I S a S S E M B L Y a N D a S S E M B L YAssembly Frame SeparationDiagnostic Fault Codes I I . B a S I C TroubleshootingWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Axle Bearings and the MOTOR/TRANSAXLE Assembly Wheel ReplacementMotor Brushes CONSOLE, CHARGER, and Rear ElectronicsFuse Replacement Nylon Lock NUT ReplacementEvent a fuse should cease to work Storing Your ScooterT E S Page INFMANU4206
Top Page Image Contents