Pride Mobility INFMANU4206 manual C a R E a N D M a I N T E N a N C E

Page 39

I X . C A R E A N D M A I N T E N A N C E

Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your ability to perform the maintenance listed below, you may schedule inspection and maintenance at your authorized Pride Provider. The following areas require periodic inspection and/or care and maintenance.

TIRE PRESSURE

If equipped with pneumatic tires, always maintain the psi/bar/kPa air pressure rating indicated on each tire.

WARNING! It is important that the psi/bar/kPa air pressure rating indicated on each tire be maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and overinflated tires may burst. Failure to maintain the psi/bar/kPa air pressure rating indicated on the tires at all times may result in tire and/or wheel failure.

Regularly inspect your scooter’s tires for signs of wear.

EXTERIOR SURFACES

Bumpers, tires, and trim can benefit from an occasional application of a rubber or vinyl conditioner.

WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tire tread, as this may cause them to become dangerously slippery.

CLEANING AND DISINFECTION

Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter. Avoid using products that may scratch the surface of your scooter.

If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your product before application.

WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning agent before applying it to your product. Failure to comply may result in skin irritation or premature deterioration of upholstery and/or scooter finishes.

BATTERY TERMINAL CONNECTIONS

Make certain that the terminal connections remain tight and uncorroded.

The batteries must sit flat in the battery wells.

The battery terminals should face towards the outside of the scooter.

WIRING HARNESSES

Regularly check all wiring connections.

Regularly check all wiring insulation, including the charger power cord, for wear or damage.

Have your authorized Pride Provider repair or replace any damaged connector, connection, or insulation that you find before using your scooter again.

PROHIBITED! Even though the scooter has passed the necessary testing requirements for ingress of liquids, you should keep electrical connections away from sources of dampness, including direct exposure to water or bodily fluids and incontinence. Check electrical components frequently for signs of corrosion and replace as necessary.

WARNING! Do not pull on electrical harnesses directly to detach them from the scooter. Always grasp the connector itself when disconnecting the harness to prevent wire damage.

ABS PLASTIC SHROUDS

The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are coated with an advanced formula urethane paint.

A light application of car wax will help the shrouds retain their high gloss.

Victory Sport

www.pridemobility.com

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Victory Sport F E T Y G U I D E L I N E S N T E N T S Shipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Removable Parts PRE-RIDE Safety Check GeneralModifications Weight Limitations Tire InflationIncline Information S a F E T Y Your scooter is equipped with these powerful brake systems Cornering InformationBraking Information Correct Curb Approach Outdoor Driving SurfacesDoors Inclement Weather PrecautionsFreewheel Mode Stairs and EscalatorsBatteries Battery Disposal and RecyclingElevators LIFT/ELEVATION ProductsPositioning Belts Motor Vehicle TransportGetting Onto and OFF of Your Scooter Reaching and BendingFlammability Precautions Prescription DRUGS/PHYSICAL LimitationsALCOHOL/SMOKING Electromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RHi-Low Switch Turn Signal ButtonsLights Switch Hazard Lights SwitchOff-board Charger Port Electrical System FusesRear Components Anti-Tip Wheels Motor/Transaxle AssemblySafety Flag Bracket BatteriesSecuring the Scooter Main Circuit Breaker Reset ButtonCharging Your Batteries Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCan I use a different charger? Frequently Asked QuestionsFollow these easy steps to change your batteries safely How does the charger work?How can I get maximum range or distance per charge? How can I ensure maximum battery life?What type and size of battery should I use? How often must I charge the batteries?How do I change a battery in my scooter? You may need the following to change your batteriesTo change the batteries in your scooter Battery Removal/Installation Why do my new batteries seem weak?What about public transportation? Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Before Getting Onto Your ScooterGetting OFF of Your Scooter Power Down Timer FeatureMirror Position Tiller Angle AdjustmentSeatback Adjustment C O M F O R T a D J U S T M E N T SFRONT-TO-BACK Seat Adjustment Seat Height AdjustmentArmrest Angle Adjustment Seat Rotation AdjustmentTo adjust the positioning belt for operator comfort Positioning Belt OptionalTo release the positioning belt I . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyFrame Separation AssemblyI I . B a S I C Troubleshooting Diagnostic Fault CodesWhat if all the systems on my scooter seem to be dead? What if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E CONSOLE, CHARGER, and Rear Electronics Axle Bearings and the MOTOR/TRANSAXLE AssemblyWheel Replacement Motor BrushesStoring Your Scooter Fuse ReplacementNylon Lock NUT Replacement Event a fuse should cease to workT E S Page INFMANU4206
Top Page Image Contents