Pride Mobility QUANTUM 600E Seat Installation, To install the seat, Controller Installation

Page 22

I V . A S S E M B L Y

Seat Installation

Itmaybenecessarytoinstalltheseateitherpriortoinitialoperation or after transporting your power chair. If your power chair is equipped with aSynergy, Tru-Balance or Specialty seating sys- tem, refer to the information provided in separate manuals. The medium- and high-back seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to the seat, regardless of seat width or seat depth. The two main components are aluminum ex- trusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so, resulting in personal injury or damage to the chair.

To install the seat:

1.Set the trapeze bars to the desired height. To change the trapeze bar height, see V. “Comfort Adjustments.”

2.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

3.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

4.Flip the seat latch safety down.

WARNING!Makesuretheseatlatchsafetyisflipped down before using your power chair.

Controller Installation

Depending on the various configurations and options you have chosen for your power chair, it may have been shipped with- out the controller module installed in the armrest.

WARNING! Do not place the controller cable so that it can be pinched in the seat frame or power base frame.

SEAT

LATCH

SAFETY

REAR

EXTRUSION

FRONT

EXTRUSION

TRAPEZE

BARS

Figure 11. Universal Mounting System (Shown Without Armrests for Clarity)

1.Install the controller into the mounting block or under the armrest. See figure 15 or 16.

2.Tighten the setscrew(s).

3.Route the controller cable so that it cannot be pinched in the seat hinge.

4.Loosen the rear shroud fasteners and remove the rear shroud. See figure 6.

5.Plug the controller connector(s) into the power base. See figure 6.

6.Secure the controller cable to the armrest receiver with one or more wire ties.

7.Replace the rear shroud and tighten the rear shroud fasteners.

22

www.quantumrehab.com

Quantum 600E

Image 22

Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R Quantum 600EQuantum 600E Specifications Quantum 600E Power Base Electrical ComponentsQuantum 600E Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YTo install the seat Seat InstallationController Installation O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightSeatback Angle Adjustment Seat Position AdjustmentManual Recline Seatback Adjustment Armrest Angle Adjustment Armrest Width AdjustmentController Position To adjust the foot platform depth Foot Platform Height AdjustmentFoot Platform Depth Adjustment To raise or lower the foot platformSwing-away Footrests Foot Platform Angle AdjustmentElevating Leg Rests Optional Heavy Duty Drop-in Leg Rests Multi-Axis Foot PlatesBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in Frequently Asked Questions FAQsHow can I get maximum range or distance per charge? Why do my new batteries seem weak?Infrequent Use What type of batteries should I use?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickOn/Off Key Battery Condition MeterKeypad Speed/Profile KeysPower Seat Actuator Connector Motor ConnectorsBattery Connector Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Thermal RollbackTemperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksCleaning Instructions Disposal of Your Power ChairWheel Replacement Battery Replacement To replace the batteriesBattery Installation When to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S T E S Quality Control Quantum 600E