Pride Mobility QUANTUM 600E owner manual Battery Break-in, Frequently Asked Questions FAQs

Page 30

V I . B A T T E R I E S A N D C H A R G I N G

To charge the batteries using the off-board charger:

1.Position the front of your power chair next to a standard electrical outlet.

2.Becertainthecontrollerpoweris turnedoff.

3.Plug the off-board charger into the off-board charger/programming socket on the controller. SeeVII. “Operation.”

4.Plugtheoff-boardchargerintoanelectricaloutlet.

NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off- board charger, then follow the instructions supplied by the manufacturer.

5. Whenthebatteriesarefullycharged,unplugtheoff-boardchargerfromtheelectricaloutletandthenfromthecontroller.

Battery Break-in

To break in new batteries for maximum efficiency:

1.Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.

2.Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you become accustomed to the controls and break in the batteries.

3.Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now perform atover 90%oftheirpotential.

4.After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.

Frequently Asked Questions (FAQs)

How does the charger work?

The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to 24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the charger doesn’t work as hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.

Can I use a different battery charger?

You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do not recommend using other types of chargers (e.g., an automotive battery charger).

NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero voltage. If this happens, call your Quantum Rehab Specialist for assistance.

How often must I charge the batteries?

Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a daily basis or you may not use it for weeks at a time.

!Daily Use

If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair. Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the batteries 8 to 14 hours after daily use.

30

www.quantumrehab.com

Quantum 600E

Image 30
Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsWeight Limitations Tire InflationIncline Information Braking Information Cornering InformationPublic Streets and Roadways Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R Quantum 600EQuantum 600E Specifications Quantum 600E Power Base Electrical ComponentsQuantum 600E Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YSeat Installation To install the seatController Installation O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightSeat Position Adjustment Seatback Angle AdjustmentManual Recline Seatback Adjustment Armrest Width Adjustment Armrest Angle AdjustmentController Position To adjust the foot platform depth Foot Platform Height AdjustmentFoot Platform Depth Adjustment To raise or lower the foot platformFoot Platform Angle Adjustment Swing-away FootrestsElevating Leg Rests Optional Heavy Duty Drop-in Leg Rests Multi-Axis Foot PlatesB a T T E R I E S a N D C H a R G I N G Batteries and ChargingCharging the Batteries Battery Break-in Frequently Asked Questions FAQsHow can I get maximum range or distance per charge? Why do my new batteries seem weak?Infrequent Use What type of batteries should I use?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickOn/Off Key Battery Condition MeterKeypad Speed/Profile KeysPower Seat Actuator Connector Motor ConnectorsBattery Connector Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Thermal RollbackTemperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksDisposal of Your Power Chair Cleaning InstructionsWheel Replacement Battery Replacement To replace the batteriesBattery Installation When to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S T E S Quality Control Quantum 600E