Pride Mobility QUANTUM 600E Keypad, On/Off Key, Battery Condition Meter, Speed/Profile Keys

Page 34
Figure 24. VSI Controller Keypad

V I I . O P E R A T I O N

Keypad

The keypad is located in front of the joystick. It contains keys necessary to operate your power chair. See figure 24.

On/Off Key

The on/off key turns the VSI on and off.

WARNING! Unless faced with an emer- gency situation, do not use the on/off key to stop the power chair. This will cause the power chair to stop abruptly.

WARNING! Always turn the power off when you are stationary to prevent unexpected movement.

Battery Condition Meter

The battery condition meter is a 10-segment illuminated dis- play located in front of the joystick. It consists of red, yel- low, and green lights. When the lights are on, it indicates that there is power to the VSI. The lights also indicate battery status, VSI operational status, and electrical system status.

!Red, yellow, and green lights lit: Batteries charged;

VSI operational, and electrical system OK.

!Red and yellow lights lit: Charge batteries if pos-

sible; VSI operational, and electrical system OK.

!Red lights only lit or slow flash: Charge batteries

as soon as possible; VSI operational, and electrical system OK.

NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, remind- ing you the batteries need to be charged immediately!

!Rapid flash of lights: Indicates a fault in the VSI or the electrical system. Refer to “VSI Error Codes.”

!Ripple side to side of lights: The joystick was not in the neutral position when the controller was turned on. If you get “ripple side to side of lights,” turn off the controller, allow the joystick to return to the neutral position, then turn on the controller.

NOTE: If you still get “ripple side to side of lights,” contact your Quantum Rehab Specialist.

Speed/Profile Keys

The speed/profile keys control either the speed setting or the drive profile. Press the speed/profile increase key to increase the speed setting or change the drive profile to a higher number. Press the speed/profile decrease key to decrease the speed setting or change the drive profile to a lower number. The speed setting or drive profile is displayed on the maximum speed/profile indicator. If your power chair was programmed with a drive profile, contact your Quantum Rehab Specialist for more information.

NOTE: We recommend that the first few times you operate your power chair, you use the lowest speed setting until you become familiar with your new power chair.

34

www.quantumrehab.com

Quantum 600E

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Page F E T Y G U I D E L I N E S N T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Information ExchangePride Owners Club My Quantum Rehab SpecialistProduct Safety Symbols S a F E T YS a F E T Y Pre-Ride Safety Check ModificationsTire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationPublic Streets and Roadways Stationary Obstacles Steps, Curbs, etc Freewheel ModeOutdoor Driving Surfaces Stairs and EscalatorsElevators TransfersDoors Lift/Elevation ProductsPositioning Belts Inclement Weather PrecautionsMotor Vehicle Transport Reaching and BendingAlcohol Electromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R P O W E R C H a I R Quantum 600EQuantum 600E Specifications Quantum 600E Power Base Electrical ComponentsQuantum 600E Electrical Components Manual Freewheel Levers To engage or disengage the drive motorsInitial Assembly A S S E M B L YTo install the seat Seat InstallationController Installation O M F O R T a D J U S T M E N T S Comfort AdjustmentsSeat Height and Seat Angle Adjustment To change the seat heightSeatback Angle Adjustment Seat Position AdjustmentManual Recline Seatback Adjustment Armrest Angle Adjustment Armrest Width AdjustmentController Position To adjust the foot platform depth Foot Platform Height AdjustmentFoot Platform Depth Adjustment To raise or lower the foot platformSwing-away Footrests Foot Platform Angle AdjustmentElevating Leg Rests Optional Heavy Duty Drop-in Leg Rests Multi-Axis Foot PlatesBatteries and Charging B a T T E R I E S a N D C H a R G I N GCharging the Batteries Battery Break-in Frequently Asked Questions FAQsHow can I get maximum range or distance per charge? Why do my new batteries seem weak?Infrequent Use What type of batteries should I use?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?VSI consists I . O P E R a T I O NVSI Electronic Controller JoystickOn/Off Key Battery Condition MeterKeypad Speed/Profile KeysPower Seat Actuator Connector Motor ConnectorsBattery Connector Actuator Keys and Actuator Lights For Optional EquipmentVSI Error Codes Thermal RollbackTemperature Care and MaintenanceShould your power chair come in contact with water I I . C a R E a N D M a I N T E N a N C EMonthly Checks Daily ChecksWeekly Checks Yearly ChecksCleaning Instructions Disposal of Your Power ChairWheel Replacement Battery Replacement To replace the batteriesBattery Installation When to See Your Quantum Rehab Specialist for Service Corrective MaintenanceW a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byT E S T E S Quality Control Quantum 600E
Top Page Image Contents