Pride Mobility v10 C O M F O R T a D J U S T M E N T S, Tiller Angle Adjustment, Mirror Position

Page 33

V I . C O M F O R T A D J U S T M E N T S

TILLER ANGLE ADJUSTMENT

WARNING! Remove the key from the key switch before adjusting the tiller or the seat. Never attempt to adjust the tiller or the seat while the scooter is in motion.

Your scooter is equipped with an adjustable pivoting tiller.

1.While supporting the tiller, turn the tiller adjust- ment knob counterclockwise to loosen the tiller. See figure 15.

2.Move the tiller to a comfortable position.

3.Turn the tiller adjustment knob clockwise to secure the tiller in position.

NOTE: In order to fully lower the tiller for purposes of disassembly or transport, you must first completely remove the seat. See VII. “Disassembly and Assembly.”

MIRROR POSITION

To install the mirror (see figure 16):

1.Determine on which side to install the mirror and remove the rubber plug from the top of the tiller handle.

2.Insert the threaded end of the mirror holder into the opening and rotate it clockwise until snug.

3.If necessary, rotate the nut clockwise to secure the mirror in place.

To adjust the mirror:

1.Position yourself in a seated driving position fac- ing forward.

2.Adjust the mirror left, right, up, or down until you have a good line of sight behind you.

ARMREST WIDTH ADJUSTMENT

The armrest width can be adjusted inward or outward.

1.Loosen the armrest adjustment knobs. See figure 17.

2.Use the attached ring to pull and remove the detent pins.

3.Slide the armrests in or out to the desired width.

4.Align the adjustment holes on the seat frame and armrest, then reinsert the detent pin.

5.Tighten the armrest adjustment knobs.

NOTE: Pivot the armrests upward to aid in getting onto and off of your scooter.

TILLER

ADJUSTMENT

KNOB

Figure 15. Tiller Adjustment

MIRROR HOLDER

RUBBER PLUG

NUT

Figure 16. Mirror Installation and Positioning

DETENT PINS

ARMREST

ADJUSTMENT

KNOBS

Figure 17. Armrest Width Adjustment

V10

www.pridemobility.com

33

Image 33
Contents V10 F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Removable Parts PRE-RIDE Safety Check GeneralModifications Weight Limitations Tire InflationIncline Information S a F E T Y Cornering Information Your scooter is equipped with these powerful brake systemsBraking Information Outdoor Driving SurfacesCorrect Curb Approach Inclement Weather PrecautionsStairs and Escalators Freewheel ModeDoors ElevatorsLIFT/ELEVATION Products Battery Disposal and RecyclingBatteries Preventing Unintended MovementMotor Vehicle Transport Getting Onto and OFF of Your ScooterReaching and Bending Positioning Belts Flammability PrecautionsPrescription DRUGS/PHYSICAL Limitations ALCOHOL/SMOKINGElectromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RStatus LED Throttle Control Lever Batteries Rear ComponentsMain Circuit Breaker Reset Button Front Securement Points 3-Wheel Securing the ScooterB a T T E R I E S a N D C H a R G I N G Reading Your Battery VoltageBatteries and Charging Charging Your BatteriesFrequently Asked Questions How can I ensure maximum battery life? How often must I charge the batteries?How can I get maximum range or distance per charge? How do I change a battery in my scooter? What type and size of battery should I use?You may need the following to change your batteries To change the batteries in your scooterBattery Removal/Installation Why do my new batteries seem weak?Batteries for maximum efficiency and service life Follow these steps to properly break in your scooter’s newWhat about public transportation? P E R a T I O N PRE-RIDE Adjustments and ChecksBefore Getting Onto Your Scooter Getting Onto Your ScooterGetting OFF of Your Scooter Power Down Timer FeatureArmrest Width Adjustment Tiller Angle AdjustmentC O M F O R T a D J U S T M E N T S Mirror PositionSeat Rotation Adjustment FRONT-TO-BACK Seat AdjustmentSeat Height Adjustment To operate the power seat Power Seat AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyFrame Separation AssemblyDiagnostic Fault Codes I I . B a S I C TroubleshootingWhat if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E ABS Plastic Shrouds Wheel ReplacementMotor Brushes CONSOLE, CHARGER, and Rear ElectronicsNylon Lock NUT Replacement Fuse ReplacementEvent a fuse should cease to work Storing Your ScooterV10 Specifications P E N D I X I Specification SP E N D I X I Specification S SC610VPS V10 PS SpecificationsV10 PS Dimensions Page INFMANU4437