Pride Mobility v10 manual Follow these steps to properly break in your scooter’s new

Page 30

I V . B A T T E R I E S A N D C H A R G I N G

Follow these steps to properly break in your scooter’s new
batteries for maximum efficiency and service life:
1.	Fully recharge any new battery prior to its initial use. This
	charging cycle brings the battery up to about 88% of its peak
	performance level.
2.	Operate your new scooter in familiar and safe areas. Drive
	slowly at first, and do not travel too far from your home or
	familiar surroundings until you have become accustomed to
	your scooter’s controls and have properly broken in your
	scooter’s batteries.
3.	Fully recharge the batteries. They should be at over 90% of Figure 14. Battery Removal/Installation
	their peak performance level.

4.Operate your scooter again.

5.Fully recharge the batteries again.

6.After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak performance level and are able to last for an extended period of time.

What about public transportation?

If you intend to use public transportation with your scooter, you must contact the transportation provider in advance to determine their specific requirements.

30

www.pridemobility.com

V10

Image 30

Contents V10 F E T Y G U I D E L I N E S N T E N T S PURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y S a F E T Y Removable Parts PRE-RIDE Safety Check GeneralModifications Weight Limitations Tire InflationIncline Information S a F E T Y Braking Information Your scooter is equipped with these powerful brake systemsCornering Information Outdoor Driving SurfacesInclement Weather Precautions Correct Curb ApproachDoors Freewheel ModeStairs and Escalators ElevatorsBatteries Battery Disposal and RecyclingLIFT/ELEVATION Products Preventing Unintended MovementMotor Vehicle Transport Getting Onto and OFF of Your ScooterReaching and Bending Prescription DRUGS/PHYSICAL Limitations Flammability PrecautionsPositioning Belts ALCOHOL/SMOKINGElectromagnetic and Radio Frequency Interference EMI/RFI I . Y O U R S C O O T E R Tiller ConsoleStatus LED Throttle Control Lever Rear Components BatteriesMain Circuit Breaker Reset Button Securing the Scooter Front Securement Points 3-WheelBatteries and Charging Reading Your Battery VoltageB a T T E R I E S a N D C H a R G I N G Charging Your BatteriesFrequently Asked Questions How can I ensure maximum battery life? How often must I charge the batteries?How can I get maximum range or distance per charge? You may need the following to change your batteries What type and size of battery should I use?How do I change a battery in my scooter? To change the batteries in your scooterWhy do my new batteries seem weak? Battery Removal/InstallationBatteries for maximum efficiency and service life Follow these steps to properly break in your scooter’s newWhat about public transportation? Before Getting Onto Your Scooter PRE-RIDE Adjustments and ChecksP E R a T I O N Getting Onto Your ScooterPower Down Timer Feature Getting OFF of Your ScooterC O M F O R T a D J U S T M E N T S Tiller Angle AdjustmentArmrest Width Adjustment Mirror PositionSeat Rotation Adjustment FRONT-TO-BACK Seat AdjustmentSeat Height Adjustment Power Seat Adjustment To operate the power seatDisassembly I . D I S a S S E M B L Y a N D a S S E M B L YAssembly Frame SeparationI I . B a S I C Troubleshooting Diagnostic Fault CodesWhat if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E Motor Brushes Wheel ReplacementABS Plastic Shrouds CONSOLE, CHARGER, and Rear ElectronicsEvent a fuse should cease to work Fuse ReplacementNylon Lock NUT Replacement Storing Your ScooterP E N D I X I Specification S V10 SpecificationsP E N D I X I Specification S V10 PS Specifications SC610VPSV10 PS Dimensions Page INFMANU4437