Pride Mobility v10 manual Wheel Replacement, ABS Plastic Shrouds, Motor Brushes

Page 41

I X . C A R E A N D M A I N T E N A N C E

WHEEL REPLACEMENT

If your scooter is equipped with pneumatic tires and you have a flat tire, you can have the tube replaced. If your scooter is equipped with a solid tire insert, either the solid insert or the entire wheel must be replaced depending on the model. Contact your authorized Pride Provider for information regarding replacement wheels for your scooter.

WARNING! Wheels on your scooter should only be serviced/replaced by an authorized Pride Provider or qualified technician.

WARNING! Be sure that the key is removed from the key switch and the scooter is not in freewheel mode before performing this procedure.

AXLE SLOT

WASHER

AXLE

KEY

DRIVE WHEEL NUT

WHEEL CAP

Figure 24. Solid Tire Wheel Removal

Follow these easy steps for a quick and safe repair for solid tires:

1.Remove the key from the key switch.

2.Elevate the side of the scooter of which you are removing the tire. Place wooden blocks under the frame to elevate the scooter.

3.Remove the drive wheel nut and washer from the axle. See figure 24.

4.Pull the wheel off the axle.

5.Slide the new wheel back onto the axle.

WARNING! Ensure that the axle key is properly installed into the axle slot when mounting the wheel. If not installed securely, the braking system is disengaged which may cause personal injury and/or product damage may result.

6. Reinstall the drive wheel nut and washer onto the axle and tighten.

WARNING! Make sure that both the nut and washer are reinstalled and tightened properly.

7. Remove the blocks from beneath the scooter.

ABS PLASTIC SHROUDS

The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are coated with an advanced formula urethane paint.

A light application of car wax will help the shrouds retain their high gloss.

AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY These items are all prelubricated, sealed, and require no subsequent lubrication.

MOTOR BRUSHES

The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodi- cally for wear by your authorized Pride Provider.

CONSOLE, CHARGER, AND REAR ELECTRONICS

Keep these areas free of moisture.

Allow these areas to dry thoroughly if they have been exposed to moisture before operating your scooter again.

V10

www.pridemobility.com

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents V10 F E T Y G U I D E L I N E S N T E N T S N T R O D U C T I O N SafetyPURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y S a F E T Y Modifications Removable Parts PRE-RIDE Safety CheckGeneral Incline Information Weight LimitationsTire Inflation S a F E T Y Cornering Information Your scooter is equipped with these powerful brake systemsBraking Information Outdoor Driving SurfacesCorrect Curb Approach Inclement Weather PrecautionsStairs and Escalators Freewheel ModeDoors ElevatorsLIFT/ELEVATION Products Battery Disposal and RecyclingBatteries Preventing Unintended MovementReaching and Bending Motor Vehicle TransportGetting Onto and OFF of Your Scooter Positioning Belts Flammability PrecautionsPrescription DRUGS/PHYSICAL Limitations ALCOHOL/SMOKINGElectromagnetic and Radio Frequency Interference EMI/RFI Tiller Console I . Y O U R S C O O T E RStatus LED Throttle Control Lever Batteries Rear ComponentsMain Circuit Breaker Reset Button Front Securement Points 3-Wheel Securing the ScooterB a T T E R I E S a N D C H a R G I N G Reading Your Battery VoltageBatteries and Charging Charging Your BatteriesFrequently Asked Questions How can I get maximum range or distance per charge? How can I ensure maximum battery life?How often must I charge the batteries? How do I change a battery in my scooter? What type and size of battery should I use?You may need the following to change your batteries To change the batteries in your scooterBattery Removal/Installation Why do my new batteries seem weak?What about public transportation? Batteries for maximum efficiency and service lifeFollow these steps to properly break in your scooter’s new P E R a T I O N PRE-RIDE Adjustments and ChecksBefore Getting Onto Your Scooter Getting Onto Your ScooterGetting OFF of Your Scooter Power Down Timer FeatureArmrest Width Adjustment Tiller Angle AdjustmentC O M F O R T a D J U S T M E N T S Mirror PositionSeat Height Adjustment Seat Rotation AdjustmentFRONT-TO-BACK Seat Adjustment To operate the power seat Power Seat AdjustmentI . D I S a S S E M B L Y a N D a S S E M B L Y DisassemblyFrame Separation AssemblyDiagnostic Fault Codes I I . B a S I C TroubleshootingWhat if the main circuit breaker repeatedly trips? C a R E a N D M a I N T E N a N C E ABS Plastic Shrouds Wheel ReplacementMotor Brushes CONSOLE, CHARGER, and Rear ElectronicsNylon Lock NUT Replacement Fuse ReplacementEvent a fuse should cease to work Storing Your ScooterV10 Specifications P E N D I X I Specification SP E N D I X I Specification S SC610VPS V10 PS SpecificationsV10 PS Dimensions Page INFMANU4437
Top Page Image Contents