Pride Mobility 6000 manual Seat Installation, To install the seat

Page 22

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Contour seats are attached to the power base with the Universal Mounting System (UMS). The UMS con- sists of universal parts that may be attached to the seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 11.

NOTE: If your power chair is equipped with a Spe- cialty Seat, Synergy Seat, or a TRU-Balance Power Positioning System, refer to the information provided in separate manuals.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

To install the seat:

1.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 11.

2.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

3.Flip the seat latch safety down.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

	SEAT LATCH SAFETY
REAR	FRONT EXTRUSION
REAR
EXTRUSION	TRAPEZE BARS

4.Install the controller and route the harness to the back of the power base. See figures 12 and 13.

MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tie- down points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

5.Loosen the rear shroud fasteners and remove the rear shroud. See figure 6.

6.Plug the controller connector into the power base. See figure 7.

7.Replace the rear shroud and tighten the rear shroud fasteners. See figure 6.

8.Secure the controller harness to the armrest receiver with wire ties. See figure 13.

Figure 11. Universal Mounting System and Contour Seat

Figure 12. Controller Harness Routing on a Synergy Seat

22

www.pridemobility.com

Quantum 6000 Series

Image 22

Contents Quantum F E T Y G U I D E L I N E S Quick Reference InformationN T E N T S IIIPURCHASER’S Agreement SafetyN T R O D U C T I O N Shipping and DeliveryProduct Safety Symbols S a F E T YS a F E T Y S a F E T Y General Guidelines Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Braking Information Freewheel ModeCornering Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces To navigate up over a curb or stationary obstacleElevators Stairs and EscalatorsDoors Lift/Elevation ProductsPositioning Belts BatteriesPrescription Drugs/Physical Limitations TransfersAlcohol/Smoking Electromagnetic and Radio Frequency Interference EMI/RFI Quantum 6000 Series Power Chair I . Y O U R P O W E R C H a I RQuantum 6000 Series Power Base Electrical ComponentsQuantum 6000 Series Electrical Components Dual Manual Freewheel Levers To operate the dual manual freewheel leversHammer Motor Package Initial Assembly A S S E M B L YSeat Installation To install the seatPower Elevating Seat Option To install the power elevating seatSeat Height and Seat Angle Adjustment Comfort AdjustmentsYou may need the following to make comfort adjustments O M F O R T a D J U S T M E N T SSeat Position Manual Recline Seatback AdjustmentTo adjust the recline angle To change the positionArmrest Angle Adjustment Seatback Angle AdjustmentArmrest Width Adjustment Armrest Height AdjustmentTo extend the controller Controller PositionTo change the controller position Foot Platform Depth Adjustment Foot Platform Height AdjustmentFoot Platform Angle Adjustment Power Elevating Seat Optional To change the seat height through toggle switchB a T T E R I E S a N D C H a R G I N G Batteries and ChargingBattery Break-in Frequently Asked Questions FAQsInfrequent Use Why do my new batteries seem weak?Daily Use How can I get maximum range or distance per charge?What about public transportation? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about shipping?Temperature Care and MaintenanceShould your power chair come in contact with water I . C a R E a N D M a I N T E N a N C ETo check the brakes Daily ChecksWeekly Checks Monthly ChecksWheel Replacement Disposal of Your Power ChairCleaning and Disinfection StorageBattery Replacement Quantum 6000 Drive WheelBattery Installation To replace the batteriesWhen to See Your Quantum Rehab Provider for Service Corrective MaintenanceI I . W a R R a N T Y Service Checks and Warranty Service Reconditioned Units WarrantyWarranty Exclusions Exclusions also include components with damage caused byP E N D I X I Specification S SpecificationsQuantum 6000 Dimensions and Ground Clearance T E S T E S T E S Quality Control Quantum 6000 Series Product Serial #

Related manuals

Manual 2 pages 14.64 Kb