Pride Mobility 1170XL manual You may need the following to replace your batteries

Page 35
Figure 22. Battery Wiring Diagram

V I I . C A R E A N D M A I N T E N A N C E

You may need the following to replace your batteries:

„ metric/standard socket set and ratchet „ adjustable wrench

To replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See III.

“Your Power Chair.” 3. Unplug the connectors from the electronics tray.

4. Remove the seat. See V. “Comfort Adjustments.” 5. Remove the shroud.

6. Disconnect the wiring harnesses from the batteries.

7. Remove the batteries from the power base.

8. Place the new batteries in the power base. Make sure that the terminals are facing inwards. If the battery terminals are in the middle of the batteries, then make sure that the positive terminal of the rear battery is facing the negative terminal of the front battery on the left side.

9. Looking at the power base from the front, connect the red wire from the left side to the positive (+) terminal on the back battery and connect the black wire from the left side to the negative (-) terminal on the front battery.

WARNING! Make sure you tighten the fasteners so that the connections are secure.

10.Connect the red wire from the right side to the positive (+) terminal on the front battery and connect the black wire from the right side to the negative (-) terminal on the rear battery.

11.Reinstall the shroud.

12.Reinstall the seat.

13.Plug in the connectors to the electronics tray.

When to See Your Authorized Pride Provider for Service

The following symptoms could indicate a serious problem with your power chair. If necessary, contact your authorized Pride Provider. When calling, have the model number, serial number, nature of the problem, and the trouble code if available.

„Motor noise

„Frayed harnesses

„Cracked or broken connectors

„Uneven wear on any of the tires

„Jerky motion

„Pulling to one side

„Bent or broken wheel assemblies

„Does not power up

„Powers up, but does not move

„Loose seat or seating components

Corrective Maintenance

If the battery condition meter does not light up when you turn on the power:

„Check the harness connections. Make sure they are tight.

„Check the circuit breaker. Reset it if necessary.

„Check the battery connections.

If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up, contact your authorized Pride Provider.

Jazzy 1170 XL Plus Series

www.pridemobility.com

35

Image 35
Contents Jazzy 1170XL Plus Quick Reference Information F E T Y G U I D E L I N E SIII N T E N T SShipping and Delivery SafetyN T R O D U C T I O N PURCHASER’S AgreementS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y Modifications Pre-Ride Safety CheckGeneral Guidelines Incline Information Weight LimitationsTire Inflation Cornering Information Freewheel ModeBraking Information Stationary Obstacles Steps, Curbs, etc Inclement Weather PrecautionsPublic Streets and Roadways Outdoor Driving Surfaces Lift System/Elevation Products Stairs and EscalatorsDoors ElevatorsBatteries Positioning BeltsPrescription Drugs/Physical Limitations TransfersAlcohol/Smoking I . Y O U R P O W E R C H a I R Jazzy 1170 XL Plus Series Power ChairElectronics Tray Jazzy 1170XL Plus Series Power Base Shroud RemovedActive-Trac Suspension Manual Freewheel Levers To engage or disengage the freewheel featureA S S E M B L Y Initial AssemblyTo install the seat Seat InstallationO M F O R T a D J U S T M E N T S Comfort AdjustmentsYou may need the following to make comfort adjustments Seat Height and Seat Angle AdjustmentArmrest Height Adjustment Manual Recline Seatback AdjustmentSeatback Angle Adjustment Armrest Width AdjustmentTo extend the controller Armrest Angle AdjustmentTo change the armrest angle Controller PositionAnti-Tip Wheels Foot Platform Height AdjustmentFoot Platform Angle Adjustment To release the positioning belt To install the positioning beltTo adjust the positioning belt for operator comfort Positioning BeltCharging the Batteries B a T T E R I E S a N D C H a R G I N GBatteries and Charging Frequently Asked Questions FAQs Battery Break-inHow can I get maximum range or distance per charge? Why do my new batteries seem weak?„ Daily Use „ Infrequent UseWhat about shipping? How can I ensure maximum battery life?How should I store my power chair and its batteries? What about public transportation?I . C a R E a N D M a I N T E N a N C E Care and MaintenanceShould your power chair come in contact with water TemperatureMonthly Checks Daily ChecksWeekly Checks To check the brakesYearly Checks Disposal of Your Power ChairCleaning and Disinfection Wheel ReplacementJazzy 1170XL Plus Series Drive Wheel Battery ReplacementYou may need the following to replace your batteries When to See Your Authorized Pride Provider for ServiceCorrective Maintenance Specifications P E N D I X I Specification SJazzy 1170XL Plus Dimensions and Ground Clearance T E S Page Product Serial # Quality Control Jazzy 1170XL Plus Series