Invacare RBL250 Replacing the Rubber Pads Figures, Bath Lift Base Frame Existing Rubber Pad

Page 3

4.Twisting EXISTING suction cup from side, pull the the suction cup off of the bath lift base frame (FIGURE 10).

Bath Lift

Base Frame

EXISTING Locking Clip

EXISTING Suction Cup

FIGURE 10 - REMOVING THE EXISTING

SUCTION CUP

5.LeaveEXISTING lockingcliponthebathliftbaseframe (it is glued in place).

6.Install the NEW suction cup by reversing STEP 4.

7.Place NEW end plug into the bath lift base frame and using a hammer gently tap the end plug securely into position (FIGURE 12).

Base Frame Locking Clip

New End

Screwdriver

Bath Lift

 

Base Frame

EXISTING End Plug

 

 

NOTE: Rubber Pad

 

removed for clarity.

FIGURE 12 - REMOVING THE EXISTING

END PLUG

4.TwistingEXISTING Rubber Pad fromside,pullthe the suction cup off of the bath lift base frame (FIGURE 13).

Bath Lift Base Frame

EXISTING Rubber Pad

FIGURE 13 - REMOVING THE EXISTING

RUBBER PAD

5. Install the NEW rubber pad by reversing STEP 4.

Suction Cup

Plug

6. Place NEW end plug into the bath lift base frame and

use a hammer to gently tap the end plug securely into

FIGURE 11 - INSTALLING END PLUG

8.Repeat STEPS 2-7 on second suction cup.

9.Tilt the Bath Lift foward so that it is resting in the upright position.

10.Perform one (1) of the following:

A.Replace Rubber Pads, refer to REPLACING THE RUBER PADS in this instruction sheet.

B.Reinstall the Bath Lift into the bath tub, refer to

INSTALLING THE BATHLIFT INTO THE BATH TUB in this instruction sheet.

REPLACING THE RUBBER PADS (FIGURES 12-14)

1.Tilt Bath Lift foward so that it rests on the front por- tion of the frame and top edge of the top cover.

WARNING

Always point the screwdriver away from your body. Otherwise injury may occur.

2.Place screwdriver behind the lip of the EXISTING end plug (FIGURE 12).

3.Use a hammer to gently tap the back of the screw- driver until the EXISTING end plug comes free.

position (FIGURE 14).

Bath Lift Base Frame

NEW End Plug

NEW RubberPad

FIGURE 14 - INSTALLING END PLUG

7.Repeat STEPS 2-6 on second rubber pad.

8.Tilt the Bath Lift back to the upright position.

9.Reinstall the Bath Lift into the bath tub, refer to

INSTALLING THE BATHLIFT INTO THE BATH TUB in this instruction sheet.

INSTALLING THE BATH LIFT INTO THE BATHTUB (FIGURE 15)

NOTE: Refer to the GENERAL WARNINGS in the SAFTY SUMMARY of this Instruction Sheet.

1.Clean tub and wipe suction cups with a damp cloth.

2.Place the bath lift base frame in the bathtub (FIG- URE 15).

3.Position the rear pads of the frame just in front of the curve at the bottom of the back of the bath.

3

Image 3
Contents Pull UP to Safety SummaryReplacing the Bath Lift Mounts Removing the Bath Lift Seat FiguresLift the Seat To InstallRemoving the Bath Lift from the Bathtub Figure Replacing Suction Cups FiguresSuction Cup Plug Installing the Bath Lift Into the Bathtub FigureReplacing the Rubber Pads Figures Bath Lift Base Frame Existing Rubber PadLower Seat Frame Battery PackPull UP to é RemovePositioning the Bath Lift Frame Bathtub FigurePress Down on Suction CUP Page Limited Warranty USA