Invacare Pronto M71 manual Removing/Installing the Seat Assembly

Page 50

SECTION 7—SEAT

Removing/Installing the Seat Assembly

WARNING

DO NOT store items under seat - interference with seat latch may result.

NOTE: For this procedure, refer to FIGURE 7.4.

Removing

1.Disconnect the joystick. Refer to Disconnecting/Connecting the Joysticks on page 42.

2.Push down on the latch bar underneath front of seat.

3.Tilt front edge of seat up.

4.Slide the seat assembly forward to disengage seat from the pivot brackets located in the rear.

Installing

1.Position the seat in the rear pivot brackets as shown in FIGURE 7.4.

2.Tilt front edge of seat down.

3.When seat is lowered, engage seat brackets into seat clevis pins.

WARNING

When reinstalling the seat verify that the seat brackets are engaged with the seat clevis pins by pulling up on the latch bar.

4.Pull up on latch bar to verify that brackets are engaged with seat clevis pins.

5.Connect the joystick. Refer to Disconnecting/Connecting the Joysticks on page 42.

NOTE: Van Seat model shown. ASBA seat removes/ installs in the same way.

FIGURE 7.4

Rear Pivot

Brackets

Seat Clevis Pins

Latch Bar (located under the front of the seat)

Removing/Installing the Seat Assembly

Pronto® M94™

50

Part No. 1122145

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Pronto M94 Dealer This manual Must be given to the user of the productManual Part Number Reference DocumentsReference Documents Table of Contents Wheelchair Operation ArmsFront Riggings Footboard AssemblySeat SHROUD/WHEELS Limited WarrantyRegister Your Product BatteriesWheelchair TIE-DOWN Restraints and Seat Restraints Signal Word MeaningSpecial Notes Special Notes Label Locations Typical Product Parameters InchOperation Information Controller Settings/Repair or ServiceGeneral Guidelines General Guidelines Charging Batteries AccessoriesBatteries Grounding Instructions Weight TrainingWeight Limitation Rain TestEMI Information EMI InformationEMI Information SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping With Everyday Obstacles Lifting/Stairways Rear Forks Front Forks Transferring to and From Other Seats Reaching, Leaning and Bending ForwardReaching and Bending Backward Reaching, Leaning and Bending ForwardInspect/Adjust Initially Safety INSPECTION/ TroubleshootingSafety Inspection Checklists Inspect/Adjust Periodically Inspect/Adjust WeeklyInspect/Adjust Monthly Solutions Troubleshooting MechanicalTroubleshooting Electrical SPJ+, SPJ+ w/PSS or SPJ+ w/ACC JoysticksNumber Error Code Possible Solution Display Description DefinitionSymptom Probable Cause Solutions MPJ+, PSR+, PSF+ Joysticks or DisplaysDealer/Invacare for Service Checking Battery Charge Level DON’TOperating the Wheelchair Turning the Power On/OffWheelchair Operation Joystick ActionUsing the Joystick to Drive the Wheelchair Movement ActionOn/Off Button SpeedometerJoystick Service IndicatorSpeed Control Buttons Charger/Programming InputInformation Gauge Display MPJ+ Joystick Switches and IndicatorsDrive Select Toggle Switch Speed Control LCD Display ScreensLCD Display LCD Display Screens Driving Programmable Mono Port 1/2 or External Mode Switch IconMemory Card Slot Remote On/Off SwitchMode Switch Asba Seat Model Preparing the Joystick for UseRepositioning the Joystick Van Seat Model 10 Repositioning the Joystick Asba Seat ModelDisconnecting/Connecting the Joysticks SPJ+ Joysticks13 Disconnecting/Connecting the Joysticks MPJ+ Joysticks MPJ+ JoysticksArms Installing/Removing Flip Back ArmrestsInstalling RemovingPositioning Flip Back Armrests for User Transfer Adjusting Flip Back ArmrestsAdjusting Positioning Flip Back Armrests for UseHeight Adjusting Van Seat ArmrestsAngle Adjusting Van Seat Armrests Seat Adjusting the HeadrestAdjusting the Back Angle Adjustable Seat Back Angle Asba Model Removing/Installing the Seat Assembly Adjusting the Seat Height Adjusting Seat Position on Seat Frame Asba ModelAdjusting Seat Depth Van Seat Only Do not UseAdjusting Seat Depth Van Seat Only Replacing the Seat Positioning StrapReplacing the Seat Positioning Strap Asba Model Footboard Assembly Removing/Installing the Footboard AssemblyAdjusting the Footboard Assembly Removing/Installing the Footboard AssemblyAdjusting the Footboard Assembly Depth DepthInstalling/Removing Front Riggings Front RiggingsModel PH904A and PHAL4A Adjusting Footrest HeightModel PHWH93 Replacing Heel Loops Raising/Lowering Elevating Front RiggingsFront Riggings Adjusting/Replacing Telescoping Front Rigging Supports Asba Standard Position Inch OUT Inches OUTAdjusting/Replacing Telescoping Front Rigging Supports Asba Replacing the Flat Free Tires on the Wheel Rim Removing/Installing the ShroudsSHROUD/WHEELS Removing/Installing the Shrouds Engaging/Disengaging Motor Release LeverReplacing Front/Rear Caster Assemblies Engaging/Disengaging Motor Release LeverAdjusting Forks Adjusting ForksBatteries Installing/Removing the Batteries Tool QTY CommentsInstalling/Removing the Batteries Connecting/Disconnecting the Battery Wiring Harness Connecting DisconnectingConnecting/Disconnecting the Battery Wiring Harness Charging BatteriesWhen to Charge Batteries SPJ+ JoysticksMPJ+ Joystick Battery Charger OperationOn-Board Battery Charger Charging Indicator Status YellowIndependent Charger Independent ChargerBatteries Limited Warranty USA

Pronto M71 specifications

The Invacare Pronto M71 is a state-of-the-art power wheelchair designed for users seeking enhanced mobility and independence. Known for its compact design, the Pronto M71 is versatile enough for both indoor and outdoor use, making it an ideal choice for individuals with varying mobility needs.

One of the standout features of the Pronto M71 is its advanced SureStep technology. This innovative system allows the wheelchair to navigate over obstacles and transitions smoothly, ensuring users can move confidently across uneven surfaces. The SureStep system features a unique suspension mechanism that helps maintain stability and control, which is particularly beneficial when negotiating ramps or curbs.

The Pronto M71 is powered by a robust drivetrain comprised of strong motors that provide reliable performance. It is equipped with dual motors that enhance maneuverability, allowing the chair to turn on a dime and navigate tight spaces with ease. The wheelchair's rear-wheel drive design further contributes to its stability and straight-line tracking, giving users a sense of security during transit.

Comfort is a top priority for Invacare, and the Pronto M71 is no exception. The chair features adjustable seating systems, providing users with the option to customize their seating to fit their specific needs. This includes adjustable armrests, seat depth, and back height, ensuring maximum comfort for users during extended periods of use.

In terms of safety, the Pronto M71 is designed with thoughtful features that prioritize user protection. The chair comes with anti-tip technology, ensuring stability when navigating slopes or uneven terrain. Additionally, powerful brakes provide dependable stopping performance, giving users confidence in their mobility.

Another notable characteristic of the Pronto M71 is its user-friendly controls. The joystick controller is intuitive and easy to operate, allowing for effortless navigation. The buttons are designed for simplicity, making it accessible for users of all ages and abilities.

The Pronto M71 also supports various accessories, including trays, cup holders, and custom seating, making it a highly adaptable solution to meet individual user preferences.

Overall, the Invacare Pronto M71 power wheelchair is a remarkable blend of technology, comfort, and safety. Whether users are navigating their home or exploring the outdoors, the Pronto M71 offers the performance and reliability needed to enjoy an active and independent lifestyle. Its innovative features and focus on user experience make it a top choice in the market for power wheelchairs.
Top Page Image Contents