Allegro Industries 9832 L E R a N C E S a N D W a R N I N G S, AIR Pump, Explosion Proof Pump

Page 6

T O L E R A N C E S A N D W A R N I N G S

Allegro ambient air pumps are precision pumps that have only .0015-.003 clearance between the top of the rotor and cylinder bore, and .003 or less clearance between end of the rotor and the end plate. Any thrust on the shaft such as mishandling or dropping the pump on its end will tend to close these clearances, causing the rotor to jam. Foreign particles, excessive dirt or dust build up may cause sluggish performance and eventual “jamming” of the pump. The pumps have carbon vanes and grease packed bearings. They MUST NOT be lubricated or flushed with petroleum base solvents.

All models have precision ground vanes inside the pump that take up their own wear and will last approximately 3,000 hours, depending upon workload, maintenance, speed and degree of pressure. Excessive dirt, foreign particles, or moisture could cause the vanes to stick in the rotor slots and even break. Periodic “flushing” could prevent this. Use the Allegro flushing cleaner (P/N: 9700-65) in the pump chamber only.

CAUTION!

The basic materials used in the pumps are cast iron and steel. Consequently, any moisture will tend to corrode the interior, especially when pump stands idle for extended periods.

AIR PUMP: (9850)

oThe motor for the Air driven pump is a precision built rotary-type motor. The vanes for this motor take up their own wear and will last 5,000 to 15,000 hours depending upon speed, operating pressure, and the precautions

taken in maintaining the motor.

oThe type of shaft seal used does not lend itself to operating pressures above 100 psi (6.89 bar).

oThe air motor requires a minimum of 75 cfm at 80 psi inlet pressure and volume to operate pump.

oThe starting torque is less than the running torque and could vary depending on the position at which the vanes stop in relation to the air intake port.

oThe speed and torque can be regulated by using the pressure regulator or shut-off ball valve to obtain desired power.

EXPLOSION PROOF PUMP: (9833)

•The Ambient air pump is rated for use in hazardous locations, however the user must ensure that the following guidelines are followed:

o The inlet filter (or Extension) must not be in a hazardous environment; this will endanger the respirator user. Inlet filter must be in a clean uncontaminated environment at all times.

o Testing of ambient location where inlet filter is placed is strongly recommended, to ensure it meets CGA specifications of grade D or higher.

•The pump is rated to be used in the following hazardous locations: o Class I, Group D

o Class II, Group F and G

•Verify your location classification.

o Ensure the pump design meets the hazardous class and group classifications of job site.

o The National Electric Code divides these locations into Classes and Groups according to the type of explosive gas/agent, which may be present.

o For specific information, consult the National Electric Code, Section 500.

•The Hazardous Location plug and receptacle must be used to hardwire the pump to the power source. Consult a qualified electrician and the National Electric Code articles 500 through 517.

CAUTION!

Hazardous location equipment may be required in any area where the presence of flammable gases, vapors or finely pulverized dusts in the atmosphere is sufficient to create a threat of explosion or fire. It may also be required where easily ignitable fibers of flyings are present.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Allegro INTRODUCTION/DESCRIPTION Table of ContentsNumber Tolerances and WarningsIntroduction DescriptionAIR Driven Pump P/N A. Grade-D Air RequirementsE R ’ S I N S T R U C T I O N S Pressure Relief Valve RPVInlet Extension KIT P/N L E R a N C E S a N D W a R N I N G S AIR PumpExplosion Proof Pump Electrical Motors Specification SS P E C T I O N ALL Pumps AIR Driven MotorsI N T E N a N C E Filters Flushing InstructionsAIR Driven Motor P/N Models A-750, A-750TE R T S & a C C E S S O R I E S All ModelsModel A-300 Models A-1500TE, A-1500EX, A-4000ADIf output air hot or pump is running hot Troubleshooting Electric ModelsIf motor fails If there is a rise in outlet pressureIf low torque or speed, or motor runs hot If there is a drop in outlet pressureAIR Driven Pump If motor won’t turn at allWarranty Limitation of LiabilityReturn Policy Ambairpumman.doc Rev C /03

9832, 9806, 9850, 9833, 9846 specifications

Allegro Industries is a renowned manufacturer, specializing in a range of high-performance portable ventilation systems that cater to various industrial needs and environments. Among their celebrated offerings are the models 9821, 9846, 9833, 9850, and 9806, each designed with unique features that enhance productivity and safety in the workplace.

The model 9821 stands out due to its lightweight portable design, making it ideal for use in confined spaces or remote locations. This model boasts a powerful motor that generates a high volume of air movement, ensuring a steady flow of fresh air even in the most challenging environments. Additionally, it incorporates a rechargeable battery option, providing convenience and flexibility for users without direct access to power sources.

In contrast, the Allegro 9846 model is engineered for heavy-duty applications. It is equipped with a robust construction that can withstand the rigors of industrial workloads. Its high-efficiency fan system is designed to deliver maximum airflow while consuming minimal energy. This model is particularly effective in large spaces where effective ventilation is essential for maintaining air quality and worker safety.

The 9833 model takes a different approach by integrating advanced filtration technologies. This model includes a multi-stage filtration system that effectively captures dust, pollutants, and other airborne particles, making it suitable for environments that require clean air standards. The compact design allows easy transport and setup, ensuring it can be deployed swiftly when needed.

Model 9850 is designed for versatility, featuring a modular design that allows users to customize airflow parameters according to their specific requirements. With dual fan capabilities and the option for daisy chaining multiple units, this model is perfect for both small and expansive operations. Its intuitive controls make it user-friendly, allowing operators to adjust settings quickly while ensuring optimal performance.

Lastly, the 9806 model emphasizes durability, featuring a rugged casing that protects internal components from damage in harsh industrial settings. It offers adjustable speed settings, allowing users to tailor airflow intensity based on the task at hand. This model is particularly well-suited for construction sites, manufacturing facilities, and emergency response applications.

Overall, Allegro Industries’ range of ventilation systems exemplifies cutting-edge engineering, providing effective air movement solutions for diverse industrial applications. Each model showcases a combination of technology, portability, and user-focused features, reinforcing Allegro's commitment to enhancing workplace safety and productivity.
Top Page Image Contents